Creep deformation of TiAl-Si alloys with aligned γ/α2 lamellar microstructures

被引：30
|
作者：
Johnson, DR [1 ]
Masuda, Y
Yamanaka, T
Inui, H
Yamaguchi, M
机构：
[1] Purdue Univ, Sch Mat Engn, W Lafayette, IN 47907 USA
[2] Kyoto Univ, Dept Mat Sci & Engn, Kyoto 6068501, Japan
来源：
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE | 2000年 / 31卷 / 10期
关键词：
D O I：
10.1007/s11661-000-0192-1
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Creep tests were conducted on directionally solidified TiAl-Si alloys to discern the effect of lamellar spacing and lamellar orientation on the high-temperature strength. Directional solidification of a Ti-43Al-3Si alloy was used to produce a model microstructure consisting of a single gamma/alpha(2) lamellar colony of controlled orientation for creep testing. Different heat treatments were used to vary the lamellar spacing and tensile creep tests were performed at 750 degrees C using applied stresses of 180, 210, and 240 MPa. In addition, ingots with large columnar grains of various lamellar orientation were also tested. The results clearly show the beneficial effect of microstructural control with the aligned microstructure having a much superior creep resistance. Furthermore, for specimens with aligned lamellar microstructure, decreasing the lamellar spacing greatly improved creep resistance, as both the primary creep strain and secondary creep rate are much smaller for materials with the fine lamellar spacing.
引用
收藏
页码：2463 / 2473
页数：11
相关论文
共 50 条
  • [21] Effect of creep deformation on creep-fatigue damage in lamellar TiAl alloy
    Park, YS
    Nam, SW
    Yang, SJ
    Hwang, SK
    MATERIALS TRANSACTIONS, 2001, 42 (07) : 1380 - 1384
  • [22] Importance of microstructural stability in creep resistance of lamellar TiAl alloys
    Yamaguchi, Masahiro
    Zhu, Hanliang
    Suzuki, Mayumi
    Maruyama, Kouichi
    Appel, Fritz
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2008, 483-84 : 517 - 520
  • [23] The role of ledges in creep of TiAl alloys with fine lamellar structures
    Wang, JN
    Nieh, TG
    ACTA MATERIALIA, 1998, 46 (06) : 1887 - 1901
  • [24] The investigation of α2 phase transformation controlled creep deformation mecha in the lamellar TiAl alloy
    Yang, SJ
    Nam, SW
    PRICM 4: FORTH PACIFIC RIM INTERNATIONAL CONFERENCE ON ADVANCED MATERIALS AND PROCESSING, VOLS I AND II, 2001, : 931 - 934
  • [25] Investigation of α2 to γ phase transformation controlling the creep deformation rate in lamellar TiAl intermetallics
    Nam, SW
    Kim, YW
    Yang, SJ
    Jung, HJ
    GAMMA TITANIUM ALUMINIDES 2003, 2003, : 371 - 377
  • [26] Creep deformation and creep microstructures of a near γ-TiAl alloy Ti-48Al-2Cr
    Es-Souni, M.
    Bartels, A.
    Wagner, R.
    Materials Science and Engineering A, 1993, A171 (1-2) : 127 - 141
  • [27] Creep behavior of γ-TiAl sheet material with differently spaced fully lamellar microstructures
    Chatterjee, A
    Mecking, H
    Arzt, E
    Clemens, H
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2002, 329 : 840 - 846
  • [28] Primary creep deformation behaviors related with lamellar interface in TiAl alloy
    Cho, HS
    Nam, SW
    Kim, YW
    METALS AND MATERIALS INTERNATIONAL, 1998, 4 (01) : 33 - 37
  • [29] Primary creep deformation behaviors related with lamellar interface in TiAl alloy
    Han Seo Cho
    Soo Woo Nam
    Young-Won Kim
    Metals and Materials, 1998, 4 : 33 - 37
  • [30] An in situ study of the transmission of deformation at interfaces in lamellar TiAl alloys
    Zghal, S
    Coujou, A
    Couret, A
    SOLID STATE PHENOMENA, 1998, 60 : 165 - 183
12345