Combined Machining of Ti-6Al-4V Alloy Using Electrochemical Milling and Electrochemical Grinding

被引:10
作者
Liu, Gangqiang [1 ]
Li, Hansong [1 ]
Niu, Shen [1 ]
Yue, Xiaokang [1 ]
Qu, Ningsong [1 ]
机构
[1] Natl Key Lab Sci & Technol Helicopter Transmiss, Nanjing 210016, Jiangsu, Peoples R China
来源
INTERNATIONAL JOURNAL OF ELECTROCHEMICAL SCIENCE | 2019年 / 14卷 / 10期
基金
中国国家自然科学基金;
关键词
Ti-6Al-4V alloy; Electrochemical milling; Electrochemical grinding; material removal rate; surface roughness; STRAY CORROSION; IMPROVEMENT; ELECTRODE; BEHAVIOR; FILMS; IRON; EDM;
D O I
10.20964/2019.10.39
中图分类号
O646 [电化学、电解、磁化学];
学科分类号
081704 ;
摘要
Ti-6Al-4V is a typical difficult-to-cut material with which it is difficult to achieve a high processing efficiency and good surface quality simultaneously using a single processing method. In this paper, a combined method that consists of electrochemical milling and grinding is proposed to solve this problem. Two types of electrodes were used in the different machining stages. First, the polarization curves for Ti-6Al-4V in 10% NaNO3 solution were obtained. Then, the maximum feed and material removal rates were studied using various electrochemical milling parameters. The resulting machined groove cross-sectional profiles were compared. Finally, the effects of electrochemical grinding on the machining results were investigated. The machined workpiece surfaces were examined using scanning electron microscopy and their roughnesses were measured using a roughometer.
引用
收藏
页码:9876 / 9887
页数:12
相关论文
共 27 条
[1]   Low temperature superplasticity through grain refinement in Ti-6Al-4V by a novel route of quench-roll-recrystallise [J].
Babu, Jalumedi ;
Dutta, Abhijit .
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2015, 4 (03) :348-352
[2]   Electrochemical superabrasive machining of a nickel-based aeroengine alloy using mounted grinding points [J].
Curtis, D. T. ;
Soo, S. L. ;
Aspinwall, D. K. ;
Sage, C. .
CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2009, 58 (01) :173-176
[3]   AES/XPS STUDY OF TRANSPASSIVE FILMS ON IRON IN NITRATE SOLUTION [J].
DATTA, M ;
MATHIEU, HJ ;
LANDOLT, D .
JOURNAL OF THE ELECTROCHEMICAL SOCIETY, 1984, 131 (11) :2484-2489
[4]   Controlling short circuiting, oxide layer and cavitation problems in electrochemical machining of freeform surfaces [J].
Demirtas, Hasan ;
Yilmaz, Oguzhan ;
Kanber, Bahattin .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2018, 262 :585-596
[5]   Improvement of hole exit accuracy in electrochemical drilling by applying a potential difference between an auxiliary electrode and the anode [J].
Fang, Xiaolong ;
Qu, Ningsong ;
Zhang, Yudong ;
Xu, Zhengyang ;
Zhu, Di .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2014, 214 (03) :556-564
[6]   A comparative study of surface integrity of Ti-6Al-4V alloy machined by EDM and AECG [J].
Hascalik, Ahmet ;
Caydas, Ulas .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2007, 190 (1-3) :173-180
[7]   Experimental and numerical investigations in electro-chemical milling [J].
Hinduja, S. ;
Pattavanitch, J. .
CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY, 2016, 12 :79-89
[8]   New cooling approach and tool life improvement in cryogenic machining of titanium alloy Ti-6Al-4V [J].
Hong, SY ;
Markus, I ;
Jeong, W .
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2001, 41 (15) :2245-2260
[9]   Simulation and Experimental Investigation of Electrochemical Mill-grinding of GH4169 Alloy [J].
Li, Hansong ;
Fu, Shuxing ;
Niu, Shen ;
Qu, Ningsong .
INTERNATIONAL JOURNAL OF ELECTROCHEMICAL SCIENCE, 2018, 13 (07) :6608-6625
[10]   Investigation of material removal in inner-jet electrochemical grinding of GH4169 alloy [J].
Li, Hansong ;
Niu, Shen ;
Zhang, Qingliang ;
Fu, Shuxing ;
Qu, Ningsong .
SCIENTIFIC REPORTS, 2017, 7