Comparison of Surface Characteristics and Micro Hardness of AISI D2 Tool Steel and LM13 Aluminum Alloy Machined under dry EDM (Green Machining) Process

被引：2

作者：

Pragadish, N. ^{[1
]}

Kumar, M. Pradeep ^{[2
]}

机构：

[1] SA Engn Coll, Dept Mech Engn, Chennai, Tamil Nadu, India

[2] Anna Univ, Dept Mech Engn, Coll Engn Guindy, Chennai, Tamil Nadu, India

来源：

FME TRANSACTIONS | 2021年 / 49卷 / 02期

关键词：

dry EDM; conventional EDM; micro structure; micro hardness;

D O I：

10.5937/fme2102488P

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

In this experimental work, the micro structure and the micro hardness of the surfaces machined under the dry EDM process is analyzed for AISI D2 tool steel and LM13 aluminum alloy. The experiments were conducted using copper tool electrode. Few modifications were made in the tool for conducting the experiments under dry EDM process. Discharge current, pulse on time, voltage, pressure, tool rotational speed and the duty factor were used as the various process parameters and their influence over the micro structure and micro hardness of the machined surfaces were analyzed. Better results were observed in the dry EDM process for AISI D2 tool steel, whereas dry EDM process did not reveal appreciable results for LM13 aluminum alloy.

引用

页码：488 / 493

页数：6

共 18 条

[1] AFM surface imaging of AISI D2 tool steel machined by the EDM process
Guu, YH
APPLIED SURFACE SCIENCE, 2005, 242 (3-4) : 245 - 250
[2] Optimum Control Parameters During Machining of LM13 Aluminum Alloy Under Dry Electrical Discharge Machining (EDM) With A Modified Tool Design
Nagarajan, Pragadish
Murugesan, Pradeep Kumar
Natarajan, Elango
MATERIALS SCIENCE-MEDZIAGOTYRA, 2019, 25 (04): : 407 - 412
[3] Machining of AISI D2 Tool Steel with Multiple Hole Electrodes by EDM Process
Prathipati, R. Prasad
Devuri, Venkateswarlu
Cheepu, Muralimohan
Gudimetla, Kondaiah
Kiran, R. Uzwal
INTERNATIONAL CONFERENCE ON RECENT ADVANCES IN MATERIALS, MECHANICAL AND CIVIL ENGINEERING, 2018, 330
[4] EFFECT OF HEAT TREATMENT ON THE SURFACE CHARACTERISTICS OF AISI D2 STEEL MACHINED BY WIRE EDM
Dhobe, M. M.
Chopde, I. K.
Gogte, C. L.
CHARACTERIZATION OF MINERALS, METALS, AND MATERIALS, 2012, : 495 - 502
[5] Comparison between EDM and grinding machining on fatigue behaviour of AISI D2 tool steel
de Jesus, Abilio M. P.
Ramos, Gisela F. S.
Gomes, Vitor M. G.
Marques, Maria J.
de Figueiredo, Miguel A. V.
Marafona, Jose D. R.
INTERNATIONAL JOURNAL OF FATIGUE, 2020, 139
[6] Effect of electrical discharge machining on surface characteristics and machining damage of AISI D2 tool steel
Guu, YH
Hocheng, H
Chou, CY
Deng, CS
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2003, 358 (1-2): : 37 - 43
[7] Experimental Investigation and Optimization of Machining Process Parameters in AISI D2 Steel Under Conventional EDM and Cryogenically Cooled EDM Process
S. VinothKumar
M. PradeepKumar
Transactions of the Indian Institute of Metals, 2017, 70 : 2293 - 2301
[8] Experimental Investigation and Optimization of Machining Process Parameters in AISI D2 Steel Under Conventional EDM and Cryogenically Cooled EDM Process
VinothKumar, S.
PradeepKumar, M.
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS, 2017, 70 (09) : 2293 - 2301
[9] Machining Performance and Surface Integrity of AISI D2 Die Steel Machined Using Electrical Discharge Surface Grinding Process
Rajesh Choudhary
Harmesh Kumar
Shankar Singh
Journal of Materials Engineering and Performance, 2013, 22 : 3665 - 3673
[10] Machining Performance and Surface Integrity of AISI D2 Die Steel Machined Using Electrical Discharge Surface Grinding Process
Choudhary, Rajesh
Kumar, Harmesh
Singh, Shankar
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2013, 22 (12) : 3665 - 3673

← 1 2 →