Tool life modeling for evaluating the effects of cutting speed and reinforcements on the machining of particle reinforced metal matrix composites

被引:11
作者
Kok, Metin [1 ]
机构
[1] Kahramanmaras Sutcu Imam Univ, Vocat Coll Educ, TR-46100 Kahramanmaras, Turkey
关键词
metal matrix composites; analysis of variance; mathematical modeling; tool life; SURFACE-ROUGHNESS; SIC PARTICLE; MACHINABILITY; ALLOY; OPTIMIZATION; WEAR; PARAMETERS; DESIGN; MMC;
D O I
10.1007/s12613-010-0318-4
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
The wear of cutting tools in the machining of 2024Al alloy composites reinforced with Al(2)O(3) particles using varying sizes and volume fractions of particles up to 23.3vol% was investigated by a turning process using coated carbide tools K10 and TP30 at different cutting speeds. Machining tests were performed with a plan of experiments based on the Taguchi method. The tool life model was developed in terms of cutting speed, size, and volume fraction of particles by multiple linear regressions. The analysis of variance (ANOVA) was also employed to carry out the effects of these parameters on the cutting tool life. The test results show that the tool life decreases with the increase of cutting speed for both cutting tools K10 and TP30, and the tool life of the K10 tool is significantly longer than that of the TP30 tool. For the tool life, cutting speed is found to be the most effective factor followed by particle content and particle size, respectively. The predicted tool life of cutting tools is found to be in very good agreement with the experimentally observed ones.
引用
收藏
页码:353 / 362
页数:10
相关论文
共 50 条
[41]   Fracture behavior of particle reinforced metal matrix composites [J].
Rabiei, A. ;
Vendra, L. ;
Kishi, T. .
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING, 2008, 39 (02) :294-300
[43]   Interaction of the cutting tools and the ceramic-reinforced metal matrix composites during micro-machining: A review [J].
Liu, Jian ;
Li, Juan ;
Xu, Chengying .
CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY, 2014, 7 (02) :55-70
[44]   Effects of Particle Clustering on the Flow Behavior of SiC Particle Reinforced Al Metal Matrix Composites [J].
Zhang Peng ;
Li Fuguo .
RARE METAL MATERIALS AND ENGINEERING, 2010, 39 (09) :1525-1531
[45]   Cutting Simulations and Experiments of Milled SIC Particle-Reinforced Aluminum Matrix Composites [J].
Wu Qiong ;
Li Da Peng ;
Shui Xiao Jug .
MATERIAL SCIENCE AND ENGINEERING TECHNOLOGY II, 2014, 856 :142-146
[46]   Investigation of cutting tool wear behaviors in machining of silicon carbide and magnesium oxide reinforced aluminum 2024 matrix composites [J].
Pul, Muharrem .
MATERIALS RESEARCH EXPRESS, 2019, 6 (10)
[47]   Effect of particle characteristics on deformation of particle reinforced metal matrix composites [J].
张鹏 ;
李付国 .
Transactions of Nonferrous Metals Society of China, 2010, 20 (04) :655-661
[48]   Effect of particle characteristics on deformation of particle reinforced metal matrix composites [J].
Zhang Peng ;
Li Fu-guo .
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, 2010, 20 (04) :655-661
[49]   Ultrasonic Vibration-Assisted Machining Particle-Reinforced Al-Based Metal Matrix Composites-A Review [J].
Liu, Xiaofen ;
Xiong, Yifeng ;
Yang, Qingwei .
METALS, 2025, 15 (05)
[50]   Simulation study of the influence of cutting speed and tool-particle interaction location on surface formation mechanism in micromachining SiCp/Al composites [J].
Liu, Junwei ;
Cheng, Kai ;
Ding, Hui ;
Chen, Shijin ;
Zhao, Liang .
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE, 2018, 232 (11) :2044-2056