Investigation of the trajectory uniformity in water dissolution ultraprecision continuous polishing of large-sized KDP crystal

被引:25
作者
Cheng, Zhipeng [1 ]
Gao, Hang [1 ]
Liu, Ziyuan [1 ]
Guo, Dongming [1 ]
机构
[1] Dalian Univ Technol, Minist Educ, Key Lab Precis & Nontradit Machining Technol, Dalian 116024, Peoples R China
基金
中国国家自然科学基金;
关键词
potassium dihydrogen phosphate crystal; water dissolution; ultraprecision continuous polishing; trajectory uniformity; flatness; PAD;
D O I
10.1088/2631-7990/abaabe
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
Large-sized potassium dihydrogen phosphate (KDP) crystals are an irreplaceable nonlinear optical component in an inertial confinement fusion project. Restricted by the size, previous studies have been aimed mainly at the removal principle and surface roughness of small-sized KDP crystals, with less research on flatness. Due to its low surface damage and high machining efficiency, water dissolution ultraprecision continuous polishing (WDUCP) has become a good technique for processing large-sized KDP crystals. In this technique, the trajectory uniformity of water droplets can directly affect the surface quality, such as flatness and roughness. Specifically, uneven trajectory distribution of water droplets on the surface of KDP crystals derived from the mode of motion obviously affects the surface quality. In this study, the material removal mechanism of WDUCP was introduced. A simulation of the trajectory of water droplets on KDP crystals under different eccentricity modes of motion was then performed. Meanwhile, the coefficient of variation (CV) was utilized to evaluate the trajectory uniformity. Furthermore, to verify the reliability of the simulation, some experimental tests were also conducted by employing a large continuous polisher. The results showed that the CV varied from 0.67 to 2.02 under the certain eccentricity mode of motion and varied from 0.48 to 0.65 under the uncertain eccentricity mode of motion. The CV of uncertain eccentricity is always smaller than that of certain eccentricity. Hence, the uniformity of trajectory was better under uncertain eccentricity. Under the mode of motion of uncertain eccentricity, the initial surface texture of the 100 mm x 100 mm x 10 mm KDP crystal did achieve uniform planarization. The surface root mean square roughness was reduced to 2.182 nm, and the flatness was reduced to 22.013 mu m. Therefore, the feasibility and validity of WDUCP for large-sized KDP crystal were verified.
引用
收藏
页数:9
相关论文
共 24 条
[1]   Large Optics for the National Ignition Facility [J].
Baisden, P. A. ;
Atherton, L. J. ;
Hawley, R. A. ;
Land, T. A. ;
Menapace, J. A. ;
Miller, P. E. ;
Runkel, M. J. ;
Spaeth, M. L. ;
Stolz, C. J. ;
Suratwala, T. I. ;
Wegner, P. J. ;
Wong, L. L. .
FUSION SCIENCE AND TECHNOLOGY, 2016, 69 (01) :295-351
[2]   NIF optical materials and fabrication technologies: An overview [J].
Campbell, JH ;
Hawley-Fedder, RA ;
Stolz, CJ ;
Menapace, JA ;
Borden, MR ;
Whitman, PK ;
Yu, J ;
Runkel, M ;
Riley, MO ;
Feit, MD ;
Hackel, RP .
OPTICAL ENGINEERING AT THE LAWRENCE LIVERMORE NATIONAL LABORATORY II: THE NATIONAL IGNITION FACILITY, 2004, 5341 :84-101
[3]  
Cheng K, 2013, MICROSYST NANOTECHNO, P1, DOI 10.1002/9781118536605
[4]  
Dmitriev VG., 1992, APPL OPTICS, V31, P6348
[5]   KDP Aqueous Solution-in-Oil Microemulsion for Ultra-Precision Chemical-Mechanical Polishing of KDP Crystal [J].
Dong, Hui ;
Wang, Lili ;
Gao, Wei ;
Li, Xiaoyuan ;
Wang, Chao ;
Ji, Fang ;
Pan, Jinlong ;
Wang, Baorui .
MATERIALS, 2017, 10 (03)
[6]   Micro water dissolution machining principle and its application in ultra-precision processing of KDP optical crystal [J].
Gao Hang ;
Wang Xu ;
Teng XiaoJi ;
Guo DongMing .
SCIENCE CHINA-TECHNOLOGICAL SCIENCES, 2015, 58 (11) :1877-1883
[7]   Experimental Study on Abrasive-Free Polishing for KDP Crystal [J].
Gao, Hang ;
Wang, Biling ;
Guo, Dongming ;
Li, Yuzhuo .
JOURNAL OF THE ELECTROCHEMICAL SOCIETY, 2010, 157 (09) :II853-II856
[8]   Research on Deliquescent Polishing Fluid for KDP Crystals [J].
Guo, S. L. ;
Zhang, F. H. ;
Zhang, Y. ;
Luan, D. R. .
ADVANCES IN MATERIALS MANUFACTURING SCIENCE AND TECHNOLOGY XIII, VOL 1: ADVANCED MANUFACTURING TECHNOLOGY AND EQUIPMENT, AND MANUFACTURING SYSTEMS AND AUTOMATION, 2009, 626-627 :53-58
[9]  
Hang Gao, 2015, International Journal of Nanomanufacturing, V11, P150
[10]  
Jiao X., 2015, CHIN J LASERS, V42, P265