Fabrication and Analysis of the Wear Properties of Hot-Pressed Al-Si/SiCp + Al-Si-Cu-Mg Metal Matrix Composite

被引：4
|
作者：
Bang, Jeongil [1 ]
Oak, Jeong-Jung [2 ]
Park, Yong Ho [1 ]
机构：
[1] Pusan Natl Univ, Dept Mat Sci & Engn, Busan 609735, South Korea
[2] Pusan Natl Univ, GCRC SOP, Busan 609735, South Korea
来源：
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE | 2016年 / 25卷 / 01期
基金：
新加坡国家研究基金会;
关键词：
aluminum; mechanical properties; metal matrix composites; microstructures; sintering; wear; DRY SLIDING WEAR; REINFORCED ALUMINUM; MATRIX COMPOSITES; ALLOYS; BEHAVIOR; MODEL; CAST;
D O I：
10.1007/s11665-015-1827-0
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
The aim of this study was to characterize microstructures and mechanical properties of aluminum metal matrix composites (MMC's) prepared by powder metallurgy method. Consolidation of mixed powder with gas atomized Al-Si/SiCp powder and Al-14Si-2.5Cu-0.5Mg powder by hot pressing was classified according to sintering temperature and sintering time. Sintering condition was optimized using tensile properties of sintered specimens. Ultimate tensile strength of the optimized sintered specimen was 228 MPa with an elongation of 5.3% in longitudinal direction. In addition, wear properties and behaviors of the sintered aluminum-based MMC's were analyzed in accordance with vertical load and linear speed. As the linear speed and vertical load of the wear increased, change of the wear behavior occurred in order of oxidation of Al-Si matrix, formation of C-rich layer, Fe-alloying to matrix, and melting of the specimen
引用
收藏
页码：102 / 115
页数：14
相关论文
共 50 条
  • [21] Characterization of Al-Si-Cu-Mg foams manufactured in-situ
    Alfonso, I.
    Figueroa, I. A.
    Bejar, L.
    Gutierrez, H. M.
    Gonzalez, G.
    Hernandez, O.
    Aguilar, C.
    Lara, G.
    JOURNAL OF ALLOYS AND COMPOUNDS, 2017, 722 : 797 - 808
  • [22] Rare Earth Metal-Based Intermetallics Formation in Al-Cu-Mg and Al-Si-Cu-Mg Alloys: A Metallographic Study
    Samuel, A. M.
    Elgallad, E. M.
    Mahmoud, M. G.
    Doty, H. W.
    Valtierra, S.
    Samuel, F. H.
    ADVANCES IN MATERIALS SCIENCE AND ENGINEERING, 2018, 2018
  • [23] The influence of abrasive size and applied load on abrasive wear of Al-Si-SiCp composite
    Singh, Raj Kumar
    Telang, Amit
    Das, Satyabrata
    ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING, 2022, 47 (07) : 8617 - 8628
  • [24] Effect of SI Content on Microstructure and Mechanical Properties of the Spray-Formed SiCp/Al-Si Composites
    Li, Wei
    Ning, Yunfei
    Chen, Jian
    Sun, YouPing
    Li, Cong
    POWDER METALLURGY AND METAL CERAMICS, 2015, 54 (5-6) : 298 - 303
  • [25] Influence of Mg and Cu on precipitation behaviors and mechanical properties of Al-Si alloys
    Xue, Li-Wen
    Jia, Hai-Long
    Ma, Pin-kui
    Song, Jia-Wang
    Zha, Min
    Wang, Hui-Yuan
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2024, 908
  • [26] Effect of extrusion ratio on the wear behaviour of Al-Si and Al-Mg alloys
    Demirci, H. I.
    Evlen, H.
    JOURNAL OF ALLOYS AND COMPOUNDS, 2012, 510 (01) : 26 - 32
  • [27] Cyclic Fatigue Fracture Behavior of Spray-Deposited SiCp/Al-Si Composite
    Li, Wei
    Chen, Jian
    Hu, Yongle
    Cong, Li
    Sun, YouPing
    Yang, JiMing
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2014, 23 (08) : 2871 - 2876
  • [28] Microstructure Evolution and Mechanical Behaviors of SiCp/CNTs Hybrid Reinforced Al-Si-Cu-Mg Composite by Semi-solid Stir Casting
    Zhang, Zhenlin
    Xiao, Ying
    Xu, Jun
    Li, Chao
    Tan, Feng-liang
    Luo, Yajun
    Liu, Kecai
    MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS, 2024, 27
  • [29] The heat treatment of Al-Si-Cu-Mg casting alloys
    Sjolander, Emma
    Seifeddine, Salem
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2010, 210 (10) : 1249 - 1259
  • [30] Artificial ageing of Al-Si-Cu-Mg casting alloys
    Sjolander, E.
    Seifeddine, S.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2011, 528 (24): : 7402 - 7409
12345