Development of TiC reinforced austenitic manganese steel

被引：18

作者：

Dalai, R. Prava ^{[1
]}

Das, S. ^{[1
]}

Das, K. ^{[1
]}

机构：

[1] Indian Inst Technol, Dept Met & Mat Engn, Kharagpur 721302, W Bengal, India

来源：

CANADIAN METALLURGICAL QUARTERLY | 2014年 / 53卷 / 03期

关键词：

Secondary processing; Elastic modulus; Impact energy; Impact wear resistance; IMPACT-WEAR RESISTANCE; ELASTIC-MODULUS; MECHANICAL-PROPERTIES; YOUNGS MODULUS; NANO-INDENTATION; POISSONS RATIO; ABRASIVE WEAR; BEHAVIOR; MICROSTRUCTURE; COMPOSITE;

D O I：

10.1179/1879139514Y.0000000140

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

The Fe-17Mn austenitic manganese steel and its in situ composite containing 10 vol.-% TiC were produced by conventional melting and casting technique. The mechanical properties such as hardness, impact toughness, elastic modulus, and impact wear resistance of the steel and composite were evaluated both in the as solutionised (1100 degrees C/1 h/WQ) and secondary processed (forged plus warm rolled) condition. It is observed that an incorporation of hard TiC particles in austenitic manganese steel as well as secondary processing help to increase the hardness, elastic modulus and impact wear resistance, but deteriorate the impact toughness.

引用

页码：317 / 325

页数：9

共 40 条

[21]

Mikihito H., 2009, T JWRI, V38, P69

[22] On the comparison of microstructural characteristics and mechanical properties of high-vanadium austenitic manganese steels with the Hadfield steel [J].

Moghaddam, E. G. ;

Varahram, N. ;

Davami, P. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2012, 532 :260-266

[23] A nano-indentation study on the mechanical behaviour of the matrix material in an AA6061 -: Al2O3 MMC [J].

Mussert, KM ;

Vellinga, WP ;

Bakker, A ;

Van Der Zwaag, S .

JOURNAL OF MATERIALS SCIENCE, 2002, 37 (04) :789-794

[24] Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology [J].

Oliver, WC ;

Pharr, GM .

JOURNAL OF MATERIALS RESEARCH, 2004, 19 (01) :3-20

[25] Investigation of mechanical and machinability properties of SiC particle reinforced Al-MMC [J].

Ozben, Tamer ;

Kilickap, Erol ;

Cakir, Orhan .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2008, 198 (1-3) :220-225

[26] Review on TiC reinforced steel composites [J].

Parashivamurthy, KI ;

Kumar, RK ;

Seetharamu, S ;

Chandrasekharaiah, MN .

JOURNAL OF MATERIALS SCIENCE, 2001, 36 (18) :4519-4530

[27] Determination of elastic modulus in a nickel alloy from ultrasonic measurements [J].

Parveen, Nikhat ;

Murthy, G. V. S. .

BULLETIN OF MATERIALS SCIENCE, 2011, 34 (02) :323-326

[28] Forming Behaviour of Al-TIC In-situ Composites [J].

Rai, Ram Naresh ;

Rao, A. K. Prasada ;

Dutta, G. L. ;

Chakraborty, M. .

LIGHT METALS TECHNOLOGY 2013, 2013, 765 :418-+

[29] Calculating the elastic modulus from nanoindentation and microindentation reload curves [J].

Shuman, David J. ;

Costa, Andre L. M. ;

Andrade, Margareth S. .

MATERIALS CHARACTERIZATION, 2007, 58 (04) :380-389

[30] Microstructures and impact toughness behavior of Al 5083 alloy processed by cryorolling and afterwards annealing [J].

Singh, Dharmendra ;

Rao, P. Nageswara ;

Jayaganthan, R. .

INTERNATIONAL JOURNAL OF MINERALS METALLURGY AND MATERIALS, 2013, 20 (08) :759-769

← 1 2 3 4 →