3D mapping of orientation variation and local residual stress within individual grains of pearlitic steel using synchrotron dark field X-ray microscopy

被引：15

作者：

Yildirim, C. ^{[1
]}

Jessop, C. ^{[2
]}

Ahlstrom, J. ^{[2
]}

Detlefs, C. ^{[1
]}

Zhang, Y. ^{[3
]}

机构：

[1] European Synchrotron Radiat Facil, 71 Ave Martyrs,CS 40220, F-38043 Grenoble, France

[2] Chalmers Univ Technol, Dept Ind & Mat Sci, S-41296 Gothenburg, Sweden

[3] Tech Univ Denmark, Dept Mech Engn, DK-2800 Lyngby, Denmark

来源：

SCRIPTA MATERIALIA | 2021年 / 197卷

基金：

欧盟地平线“2020”; 欧洲研究理事会;

关键词：

Pearlitic steels; Synchrotron radiation; X-ray diffraction (XRD); Residual stresses; MECHANICAL-PROPERTIES; GRAPHITE NODULES; ELASTIC STRAIN; TRANSFORMATION; DEFORMATION; MULTISCALE; MORPHOLOGY; KINETICS; BEHAVIOR;

D O I：

10.1016/j.scriptamat.2021.113783

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

Assessing the local residual stress and orientation with nanometer resolution within embedded steel grains has remained challenging. Here we use an advanced synchrotron technique, dark field X-ray microscopy to map 3D lattice variations, including both the crystallographic orientation and lattice strain, within two pro-eutectoid ferrite grains in pearlitic steel. We found an orientation variation up to 0.5 degrees and compressive elastic strain up to 1.8 & times; 10 & minus;3 are present in the as-manufactured sample. There is no direct correlation between the measured compressive strain and lattice orientation. The origin of the variations and their influence on the manufacturing process and mechanical properties are discussed. (c) 2021 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

引用

页数：5

共 38 条

[1] Ultra-low-angle boundary networks within recrystallizing grains [J].

Ahl, S. R. ;

Simons, H. ;

Zhang, Y. B. ;

Detlefs, C. ;

Stohr, F. ;

Jakobsen, A. C. ;

Jensen, D. Juul ;

Poulsen, H. F. .

SCRIPTA MATERIALIA, 2017, 139 :87-91

[2] DEFORMATION OF PLASTICALLY NON-HOMOGENEOUS MATERIALS [J].

ASHBY, MF .

PHILOSOPHICAL MAGAZINE, 1970, 21 (170) :399-&

[3]

Bhadeshia H.K.D.H., 2019, INT MET REV, P1

[4]

BHADESHIA HKDH, 1991, MATER SCI TECH SER, V7, P686, DOI 10.1179/026708391790184915

[5]

Bramfitt B. L., 1973, Metallography, V6, P483, DOI 10.1016/0026-0800(73)90046-3

[6] Monotonic and cyclic deformation of a high silicon pearlitic wheel steel [J].

Cvetkovski, K. ;

Ahlstrom, J. ;

Karlsson, B. .

WEAR, 2011, 271 (1-2) :382-387

[7] INFLUENCE OF STRESSES ON THE KINETICS OF PEARLITIC TRANSFORMATION DURING CONTINUOUS COOLING [J].

DENIS, S ;

GAUTIER, E ;

SJOSTROM, S ;

SIMON, A .

ACTA METALLURGICA, 1987, 35 (07) :1621-1632

[8] COUPLED TEMPERATURE, STRESS, PHASE-TRANSFORMATION CALCULATION MODEL NUMERICAL ILLUSTRATION OF THE INTERNAL-STRESSES EVOLUTION DURING COOLING OF A EUTECTOID CARBON-STEEL CYLINDER [J].

DENIS, S ;

SJOSTROM, S ;

SIMON, A .

METALLURGICAL TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1987, 18 (07) :1203-1212

[9] Microstructural Engineering in Eutectoid Steel: A Technological Possibility? [J].

Durgaprasad, A. ;

Giri, S. ;

Lenka, S. ;

Kundu, S. ;

Chandra, S. ;

Mishra, S. ;

Doherty, R. D. ;

Samajdar, I. .

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2018, 49A (05) :1520-1535

[10] Microstructures and Mechanical Properties of as-Drawn and Laboratory Annealed Pearlitic Steel Wires [J].