Experimental Investigations on the Effect of Vegetable Based Cutting Fluid in Turning AISI 1040 Steel

被引：1

作者：

Jhodkar, Durwesh ^{[1
]}

Amaranth, M. ^{[1
]}

Chelladurai, H. ^{[1
]}

Ramkumar, J. ^{[2
]}

机构：

[1] Indian Inst Informat & Technol Design & Mfg, Dept Mech Engn, Jabalpur 482005, India

[2] Indian Inst Technol, Dept Mech Engn, Kanpur 208016, Uttar Pradesh, India

来源：

ENGINEERING AND MANUFACTURING TECHNOLOGIES | 2014年 / 541-542卷

关键词：

Tool wear; flank; crater; coconut oil; TOOL WEAR; COCONUT OIL; LUBRICANTS;

D O I：

10.4028/www.scientific.net/AMM.541-542.368

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

Application of petroleum based cutting fluids in machining operation may cause many problems such as eye burn and skin inflation etc. Vegetables oils are good alternative to overcome such issues. In this work, experiments were carried out to study the influence of coconut oil on the performance of single point cutting tool insert in turning operation. Three cutting conditions viz. dry, wet and coconut oil were considered to evaluate the tool wear. Results obtained from the experiments highlighted the advantages of coconut oil, a considerable reduction in flank wear, crater wear and auxiliary wear was observed in the turning operation.

引用

页码：368 / +

页数：2

共 50 条

[41] Optimization of Process Parameters based on Surface Roughness and Cutting Force in MQL Turning of AISI 4340 using Nano Fluid
Patole, P. B.
Kulkarni, V. V.
MATERIALS TODAY-PROCEEDINGS, 2018, 5 (01) : 104 - 112
[42] Experimental investigations on machinability aspects in finish hard turning of AISI 4340 steel using uncoated and multilayer coated carbide inserts
Sahoo, Ashok Kumar
Sahoo, Bidyadhar
MEASUREMENT, 2012, 45 (08) : 2153 - 2165
[43] Improving the machining performance with bio-degradable coconut oil-assisted MQL turning of AISI-1040 steel: a sustainable machining approach
Tiwari, Saurabh
Amarnath, M.
BIOMASS CONVERSION AND BIOREFINERY, 2023, 14 (19) : 24731 - 24751
[44] STATISTICAL ANALYSIS OF HARD TURNING OF AISI 4340 STEEL ON SURFACE FINISH AND CUTTING REGION TEMPERATURE
Mohammadi, Aminollah
Zarepour, Hamid
ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES, PTS 1 AND 2, 2010, 83-86 : 303 - +
[45] Performance studies on cryogenic treated carbide cutting tool for turning of AISI304 steel
Patil, Nagraj
Gopalakrishna, K.
Sangmesh, B.
Sudhakar, K.
Vijaykumar, G. C.
JOURNAL OF MECHANICAL ENGINEERING AND SCIENCES, 2018, 12 (03) : 3927 - 3941
[46] Experimental investigation on cubic boron nitride turning of hardened AISI 52100 steel
Chou, YK
Evans, CJ
Barash, MM
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2003, 134 (01) : 1 - 9
[47] Evaluation of machining characteristics of SiO2 doped vegetable based nanofluids with Taguchi approach in turning of AISI 304 steel
Sencan, Aysegul Cakir
Sirin, Senol
Sarac, Ekin Nisa Selayet
Erdogan, Beytullah
Kocak, Mueberra Ruveyda
TRIBOLOGY INTERNATIONAL, 2024, 191
[48] Performance assessment of nano-Al2O3 enriched coconut oil as a cutting fluid in MQL-assisted machining of AISI-1040 steel
Saurabh Tiwari
M Amarnath
Munish Kumar Gupta
Mayur A. Makhesana
The International Journal of Advanced Manufacturing Technology, 2023, 129 (3-4) : 1689 - 1702
[49] Performance evaluation of minimum quantity lubrication by vegetable oil in terms of cutting force, cutting zone temperature, tool wear, job dimension and surface finish in turning AISI-1060 steel
Khan M.M.A.
Dhar N.R.
Journal of Zhejiang University-SCIENCE A, 2006, 7 (11): : 1790 - 1799
[50] Characteristics and cutting perfomance of the CVD coatings on the TiCN-based cermets in turning hardened AISI H13 steel
Liu, Junbo
Ji, Xiong
Guo, Zhixing
Qin, Chengtao
Xiao, Ya
You, Qianbing
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2020, 9 (02): : 1389 - 1399

← 1 2 3 4 5 →