Experimental Investigations on the Effect of Vegetable Based Cutting Fluid in Turning AISI 1040 Steel

被引：1
|
作者：
Jhodkar, Durwesh [1 ]
Amaranth, M. [1 ]
Chelladurai, H. [1 ]
Ramkumar, J. [2 ]
机构：
[1] Indian Inst Informat & Technol Design & Mfg, Dept Mech Engn, Jabalpur 482005, India
[2] Indian Inst Technol, Dept Mech Engn, Kanpur 208016, Uttar Pradesh, India
来源：
ENGINEERING AND MANUFACTURING TECHNOLOGIES | 2014年 / 541-542卷
关键词：
Tool wear; flank; crater; coconut oil; TOOL WEAR; COCONUT OIL; LUBRICANTS;
D O I：
10.4028/www.scientific.net/AMM.541-542.368
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
Application of petroleum based cutting fluids in machining operation may cause many problems such as eye burn and skin inflation etc. Vegetables oils are good alternative to overcome such issues. In this work, experiments were carried out to study the influence of coconut oil on the performance of single point cutting tool insert in turning operation. Three cutting conditions viz. dry, wet and coconut oil were considered to evaluate the tool wear. Results obtained from the experiments highlighted the advantages of coconut oil, a considerable reduction in flank wear, crater wear and auxiliary wear was observed in the turning operation.
引用
收藏
页码：368 / +
页数：2
相关论文
共 50 条
  • [31] Minimisation of specific cutting energy and back force in turning of AISI 1060 steel
    Paul, Sourabh
    Bandyopadhyay, P. P.
    Paul, S.
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2018, 232 (11) : 2019 - 2029
  • [32] Effect of Coconut Oil-Based Cutting Fluid on Cutting Performance During Turning With Minimal Fluid Application
    Rengiah, Robinson Gnanadurai
    INTERNATIONAL JOURNAL OF MANUFACTURING MATERIALS AND MECHANICAL ENGINEERING, 2022, 12 (01)
  • [33] EXPERIMENTAL ASSESSMENT AND TOPSIS OPTIMIZATION OF CUTTING FORCE, SURFACE ROUGHNESS, AND SOUND INTENSITY IN HARD TURNING OF AISI 52100 STEEL
    Rafighi, Mohammad
    Ozdemir, Mustafa
    Sahinoglu, Abidin
    Kumar, Ramanuj
    Das, Sudhansu Ranjan
    SURFACE REVIEW AND LETTERS, 2022, 29 (11)
  • [34] Tool Wear Behavior in μ-Turning of Nimonic 90 Under Vegetable Oil-Based Cutting Fluid
    Airao, Jay
    Kishore, Hreetabh
    Nirala, Chandrakant K.
    JOURNAL OF MICRO AND NANO-MANUFACTURING, 2021, 9 (04):
  • [35] Effect of Impact Mass on Tool Vibration and Cutting Performance During Turning of Hardened AISI4340 Steel
    Paul, P. Sam
    Varadarajan, A. S.
    ROMANIAN JOURNAL OF ACOUSTICS AND VIBRATION, 2014, 11 (02): : 154 - 163
  • [36] Experimental and numerical research on the effects of minimum quantity lubrication in thread turning of free-cutting steel AISI 1215
    An, Qinglong
    Liu, Zhiqiang
    Jiang, Li
    Chen, Ming
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2015, 229 (05) : 878 - 885
  • [37] Study on Deep Cryogenic Treated-Tempered WC-CO insert in turning of AISI 1040 steel
    Arunkarthikeyan, K.
    Balamurugan, K.
    Nithya, M.
    Jayanthiladevi, A.
    PROCEEDINGS OF 2019 INTERNATIONAL CONFERENCE ON COMPUTATIONAL INTELLIGENCE AND KNOWLEDGE ECONOMY (ICCIKE' 2019), 2019, : 661 - 664
  • [38] Optimization of the Cutting Parameters Affecting the Turning of AISI 52100 Bearing Steel Using the Box-Behnken Experimental Design Method
    Yildiz, Aytac
    Ugur, Levent
    Parlak, Ismail Enes
    APPLIED SCIENCES-BASEL, 2023, 13 (01):
  • [39] Experimental Study on Evaluating the Effect of Micro Textured Tools in Turning AISI 316 Austenitic Stainless Steel
    Vasumathy, D.
    Meena, Anil
    Duraiselvam, Muthukannan
    ADVANCES IN MATERIAL & PROCESSING TECHNOLOGIES CONFERENCE, 2017, 184 : 50 - 57
  • [40] Use of palm olein as cutting fluid during turning of mild steel
    Debnath, S.
    Anwar, M.
    Basak, A. K.
    Pramanik, Alokesh
    AUSTRALIAN JOURNAL OF MECHANICAL ENGINEERING, 2023, 21 (01) : 192 - 202
12345