Plastic mechanism analysis of fabricated square and triangular sections under axial compression

被引：19

作者：

Ye, Ji-Hong ^{[2
]}

Zhao, Xiao-Ling ^{[1
]}

Do Van Binh ^{[3
]}

Al-Mahaidi, Riadh ^{[1
]}

机构：

[1] Monash Univ, Dept Civil Engn, Clayton, Vic 3800, Australia

[2] Southeast Univ, Coll Civil Engn, Nanjing, Peoples R China

[3] Natl Univ Civil Engn, Dept Civil Engn, Hanoi, Vietnam

来源：

THIN-WALLED STRUCTURES | 2007年 / 45卷 / 02期

关键词：

plastic mechanism analysis; yield line theory; fabricated square and triangular sections; geometric imperfection; complete load-shortening behaviour; STRENGTH; CAPACITY; COLUMNS; TUBES;

D O I：

10.1016/j.tws.2007.02.006

中图分类号：

TU [建筑科学];

学科分类号：

0813 ;

摘要：

This paper presents a plastic mechanism analysis to predict the complete load-shortening behaviour of fabricated square and triangular section (FSTS) stub columns. Very high strength (VHS) circular steel tubes with a nominal yield stress of 1350 MPa are placed at each corner of the section and welded to Grade 350 steel plates to form a FSTS. Three stages are considered in the analysis: (1) both the VHS tube and steel plate are elastic, (2) plastic mechanism starts to form in steel plates while the VHS tube remains elastic (3) plastic mechanism occurs in both steel plates and the VHS tubes. Discussions are made on the factors affecting the types of mechanism ("flip-disc" versus "roof-type") in steel plates and the effect of initial geometrical imperfection of the plates on the analysis. Simplified formulae were given for an easy application of the theory developed. The predicted load-axial shortening curves are in good agreement with those obtained by experiments. The predicted ultimate load carrying capacity is about 6% to 8% lower on average than the experimental capacity. (C) 2007 Elsevier Ltd. All rights reserved.

引用

页码：135 / 148

页数：14

共 24 条

[1]

BINH DV, 2004, ADV STRUCT ENG, V7, P447

[2] Collapse strength of unstiffened conical shells under axial compression [J].

Chryssanthopoulos, MK ;

Poggi, C .

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH, 2001, 57 (02) :165-184

[3] Tension capacity of very high strength (VHS) circular steel tubes after welding [J].

Jiao, H ;

Zhao, XL .

ADVANCES IN STRUCTURAL ENGINEERING, 2004, 7 (04) :285-296

[4] Material ductility of very high strength (VHS) circular steel tubes in tension [J].

Jiao, H ;

Zhao, XL .

THIN-WALLED STRUCTURES, 2001, 39 (11) :887-906

[5]

KEY PW, 1986, P 10 AUSTR C MECH ST, P217

[6]

Korol R.M., 1972, J STRUCTURAL DIVISIO, V98, P1965

[7]

Ling TW, 2002, ADVANCES IN STEEL STRUCTURES, VOLS I & II, PROCEEDINGS, P245

[8]

LING TW, 2005, THESIS MONASH U MELB

[9] Local plastic mechanisms in thin steel plates under in-plane compression [J].

Mahendran, M .

THIN-WALLED STRUCTURES, 1997, 27 (03) :245-261

[10] ULTIMATE LOAD BEHAVIOR OF BOX-COLUMNS UNDER COMBINED LOADING OF AXIAL-COMPRESSION AND TORSION [J].

MAHENDRAN, M ;

MURRAY, NW .

THIN-WALLED STRUCTURES, 1990, 9 (1-4) :91-120

← 1 2 3 →