The effects of high-pressure injection on a compression-ignition, direct injection of natural gas engine

被引:66
|
作者
McTaggart-Cowan, G.-P.
Jones, H. L.
Rogak, S. N.
Bushe, W. K.
Hill, P. G.
机构
[1] Univ British Columbia, Dept Mech Engn, Vancouver, BC V6T 1Z4, Canada
[2] Westport Innovat Inc, Vancouver, BC V6P 6P2, Canada
关键词
alternative fuels; natural gas; direct injection; diesel pilot ignition; injection pressure;
D O I
10.1115/1.2432894
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
This study investigated the effects of injection pressure on the performance and emissions of a pilot-ignited, late-cycle direct-injected natural gas fueled heavy-duty engine. The experiments, conducted on a single-cylinder engine, covered a wide range of engine speeds, loads, and exhaust gas recirculation fractions. The injection pressure was varied at each operating condition while all other parameters were held constant. At high loads, increasing the injection pressure substantially reduced particulate matter and CO emisions ,with small increases in NOx and no significant effect on hydrocarbon emissions or fuel consumption. At low loads, injection pressure had no significant impact on either emissions or performance. At high loads, higher injection pressures consistently reduced both the number density and the size of particles in the exhaust stream. Injection pressure had reduced effects at increased engine speeds.
引用
收藏
页码:579 / 588
页数:10
相关论文
共 50 条
  • [41] Development of a Gasoline Direct Injection Compression Ignition (GDCI) Engine
    Sellnau, Mark
    Foster, Matthew
    Hoyer, Kevin
    Moore, Wayne
    Sinnamon, James
    Husted, Harry
    SAE INTERNATIONAL JOURNAL OF ENGINES, 2014, 7 (02) : 835 - 851
  • [42] Application of pilot injection strategies for enhanced ignition and combustion of a low reactivity fuel in a compression-ignition engine
    Rao, Lingzhe
    Kook, Sanghoon
    Kim, Kenneth S.
    Kweon, Chol-Bum
    APPLIED THERMAL ENGINEERING, 2022, 213
  • [43] Combined effects of diesel energy ratio and diesel injection nozzle diameter on natural gas high pressure direct injection engine with EGR
    Song, Qimin
    Wei, Lijiang
    Lu, Xiuwei
    Gao, Yufei
    Lv, Zhitao
    JOURNAL OF THERMAL SCIENCE AND TECHNOLOGY, 2023, 18 (02)
  • [44] Characteristics of High Pressure Jets for Direct Injection Gas Engine
    Yu, Jingzhou
    Vuorinen, Ville
    Kaario, Ossi
    Sarjovaara, Teemu
    Larmi, Martti
    SAE INTERNATIONAL JOURNAL OF FUELS AND LUBRICANTS, 2013, 6 (01) : 149 - 156
  • [45] Numerical Simulations of Natural Gas Injection Pressure Effects on a Direct Injected, Pilot Ignited, Natural Gas Engine
    Gao, Ying
    Li, Xiaoxiao
    Li, Jun
    Zhang, Lei
    Li, Shuhua
    MATERIALS ENGINEERING FOR ADVANCED TECHNOLOGIES (ICMEAT 2013), 2014, 510 : 179 - +
  • [46] Experimental and Computational Investigation of Diesel and Gasoline Injection in a Direct Injection Compression Ignition Engine
    Babadi, Mohammad Nazemi
    Kheradmand, Saeid
    Bae, Choongsik
    INTERNATIONAL JOURNAL OF AUTOMOTIVE TECHNOLOGY, 2020, 21 (01) : 23 - 32
  • [47] Experimental and Computational Investigation of Diesel and Gasoline Injection in a Direct Injection Compression Ignition Engine
    Mohammad Nazemi Babadi
    Saeid Kheradmand
    Choongsik Bae
    International Journal of Automotive Technology, 2020, 21 : 23 - 32
  • [48] Numerical Studies of Glow Plug Shield on Natural Gas Ignition Characteristics in a Compression-Ignition Engine
    Pan, Kang
    Wallace, James S.
    JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME, 2017, 139 (09):
  • [49] Prediction of wall impingement in a direct injection spark ignition engine by analyzing spray images for high-pressure injection up to 50 MPa
    Park, Junkyu
    Kim, Taehoon
    Kim, Donghwan
    Park, Sungwook
    FUEL PROCESSING TECHNOLOGY, 2018, 179 : 238 - 249
  • [50] Analysis of the coefficient of variation for injection pressure in a compression ignition engine
    Bakowski, Andrzej
    Radziszewski, Leszek
    Zmindak, Milan
    XXI POLISH-SLOVAK SCIENTIFIC CONFERENCE MACHINE MODELING AND SIMULATIONS MMS 2016, 2017, 177 : 297 - 302