In-Situ XRD Study of Phase Transformation Kinetics in a Co-Cr-W-Alloy Manufactured by Laser Powder-Bed Fusion

被引:9
|
作者
Hegele, Patrick [1 ]
von Kobylinski, Jonas [1 ]
Hitzler, Leonhard [1 ]
Krempaszky, Christian [1 ]
Werner, Ewald [1 ]
机构
[1] Tech Univ Munich, Inst Mat Sci & Mech Mat, Boltzmannstr 15, D-85748 Garching, Germany
来源
CRYSTALS | 2021年 / 11卷 / 02期
关键词
in-situ XRD; SLM; L-PBF; phase transformation kinetics; Co-Cr(-W)-dental alloys; residual stresses;
D O I
10.3390/cryst11020176
中图分类号
O7 [晶体学];
学科分类号
0702 ; 070205 ; 0703 ; 080501 ;
摘要
The additive manufacturing process of laser powder-bed fusion (L-PBF) is an increasingly popular approach for patient-specific production of dental frameworks made from Co-Cr alloys. Macroscopically, frameworks produced in this way exhibit high anisotropy especially in Young's modulus, and are missing standardized requirements. Microscopically, pronounced texture and high residual stresses are characteristic. To reduce resulting detrimental effects, the as-built (AB) parts are heat treated. Dependent on the treatment temperature, effects like the transformation of the gamma-phase matrix in the AB condition to epsilon-phase, precipitation, stress relief, and grain growth were observed. While the existence of these processes was established in the past, little is known about their kinetics. To fill this gap, these effects were studied with in-situ X-ray diffraction (XRD) methods in isothermal heat treatments (HTs) at four different sample surface temperatures T-S reaching from 650 degrees C to 900 degrees C. Furthermore, room temperature ex situ XRD and SEM/EDS measurements completed the analysis. An evaluation of the datasets, with single peak fitting and QXRD methods, yielded the following results. In the HTs below a certain threshold, a gamma-to-epsilon transformation was observed in the sample bulk and close to the sample surface. In the latter case, evidence for a partially strain-induced transformation related to oxide formation was present. Above this threshold and possibly slightly below, sigma- and Laves-phase precipitated. Additionally, peak profile evolutions hinted at a drop of inter- and intragranular stresses within the first 30 to 60 min. Therefore, an HT of about 30 to 60 min slightly above the threshold is proposed as optimal for reducing residual stresses while retaining a predominantly single-phased microstructure, possibly superior in corrosion properties and likewise in bio-compatibility.
引用
收藏
页码:1 / 21
页数:21
相关论文
共 50 条
  • [31] Internal Stress Evolution and Subsurface Phase Transformation in Titanium Parts Manufactured by Laser Powder Bed Fusion-An In Situ X-Ray Diffraction Study
    Schmeiser, Felix
    Krohmer, Erwin
    Schell, Norbert
    Uhlmann, Eckart
    Reimers, Walter
    ADVANCED ENGINEERING MATERIALS, 2021, 23 (11)
  • [32] Isothermal γ →ε phase transformation behavior in a Co-Cr-Mo alloy depending on thermal history during electron beam powder-bed additive manufacturing
    Yufan Zhao
    Yuichiro Koizumi
    Kenta Aoyagi
    Kenta Yamanaka
    Akihiko Chiba
    Journal of Materials Science & Technology, 2020, 50 (15) : 162 - 170
  • [33] Isothermal γ → ε phase transformation behavior in a Co-Cr-Mo alloy depending on thermal history during electron beam powder-bed additive manufacturing
    Zhao, Yufan
    Koizumi, Yuichiro
    Aoyagi, Kenta
    Yamanaka, Kenta
    Chiba, Akihiko
    JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2020, 50 : 162 - 170
  • [34] Laser powder bed fusion in-situ alloying of refractory WTa alloy and its microstructure and mechanical properties
    Li, Junfeng
    Wu, Yunxiao
    Xue, Lingfeng
    Wei, Zhengying
    ADDITIVE MANUFACTURING, 2023, 67
  • [35] The Processing Map of Laser Powder Bed Fusion In-Situ Alloying for Controlling the Composition Inhomogeneity of AlCu Alloy
    Zhou, Yang
    Chen, Xiaohan
    Zhou, Fan
    Li, Xinggang
    Huang, Yuhe
    Zhu, Qiang
    METALS, 2023, 13 (01)
  • [36] Deciphering the transformation pathway in laser powder-bed fusion additive manufacturing of Ti-6Al-4V alloy
    Chen, J.
    Fabijanic, D.
    Zhang, T.
    Lui, E. W.
    Brandt, M.
    Xu, W.
    ADDITIVE MANUFACTURING, 2022, 58
  • [37] Computational Evaluation of the Effect of Build Orientation on Thermal Behavior and in-situ Martensite Decomposition for Laser Powder-Bed Fusion (LPBF) Process
    Yildiz, Ayse Kubra
    Mollamahmutoglu, Mehmet
    Yilmaz, Oguzhan
    GAZI UNIVERSITY JOURNAL OF SCIENCE, 2023, 36 (02): : 870 - 880
  • [38] Density of additively-manufactured, 316L SS parts using laser powder-bed fusion at powers up to 400 W
    Kamath, Chandrika
    El-dasher, Bassem
    Gallegos, Gilbert F.
    King, Wayne E.
    Sisto, Aaron
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2014, 74 (1-4): : 65 - 78
  • [39] Study on the wear characteristics of INCO939 alloy manufactured by laser powder bed fusion and casting
    Karabulut, Sener
    Karakoc, Halil
    Bilgin, Musa
    Subasi, Levent
    Dursun, Gokhan
    Ozaner, Ozan Can
    TRIBOLOGY INTERNATIONAL, 2024, 194
  • [40] Effects of Cu Addition on the Microstructures and Properties of WC-12Co Cemented Carbides Additively Manufactured by Laser Powder-Bed Fusion
    Ning, Jie
    Cheng, Pei-Xin
    Qin, Ke-Jun
    Zhang, Lin-Jie
    Na, Suck-Joo
    3D PRINTING AND ADDITIVE MANUFACTURING, 2024,