In-situ observations and modeling of static recrystallization in 300 M steel

被引：52
作者：
Zhao, Mingjie [1 ]
Huang, Liang [1 ]
Zeng, Rong [1 ]
Wen, Dongxu [1 ]
Su, Hongliang [1 ]
Li, Jianjun [1 ]
机构：
[1] Huazhong Univ Sci & Technol, State Key Lab Mat Proc & Die & Mould Technol, Sch Mat Sci & Engn, Wuhan 430074, Hubei, Peoples R China
来源：
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2019年 / 765卷
基金：
中国国家自然科学基金;
关键词：
300 M steel; In-situ observations; Static recrystallization; Flow behaviors; Kinetics models; Strain-induced boundary migration; AUSTENITIC STAINLESS-STEEL; GRAIN-BOUNDARY MIGRATION; MECHANICAL-PROPERTIES; DYNAMIC RECRYSTALLIZATION; MICROSTRUCTURAL EVOLUTION; ISOTHERMAL COMPRESSION; ULTRAHIGH-STRENGTH; GROWTH-BEHAVIOR; AISI; 316L; HOT;
D O I：
10.1016/j.msea.2019.138300
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
The study of static recrystallization (SRX) has been widely concerned for its importance in regulating the microstructure and mechanical properties of deformed materials. In the paper, the effects of SRX on the flow behaviors of 300 M steel are investigated by thermal compression experiments. The SRX mechanism of 300 M steel is investigated by high temperature laser scanning confocal microscopy (HTLSCM) setup. The variations in the flow behaviors and microstructure under different experimental conditions are discussed in detail. Also, the relationships between microstructure evolution and mechanical properties are analyzed. The SRX mechanism is detected by the analysis of microstructure. According to the statistical results of microstructure, the SRX kinetics models and the average recrystallization (RX) grain size model are proposed. It can be found that the flow stress increases with the increased strain rate and reduced deformation temperature. The yield stress is affected by both the softening mechanisms of static recovery and SRX. The main SRX mechanism of 300 M steel is strain induced boundary migration (SIBM). Compared to the pre-strain rate, the insulation temperature has a more significant effect on the SRX rate, maximum SRX volume fraction and average RX grain size. And the effects of pre-strain rate on the RX grain size are negligible at low pre-strain rate. The comparison between the calculated and experimental results is consistent, which implies that the established models can describe the SRX process accurately. Besides, compared to the softening volume fraction calculated based on the stress-strain curves, the SRX volume fraction calculated based on the statistic results of microstructure can reflect the SRX process more precisely, which indicates the effectiveness of the research method used in the paper.
引用
收藏
页数：10
相关论文
共 53 条
[11]   Revealing austenite grain boundaries by thermal etching:: advantages and disadvantages [J].
de Andrés, CG ;
Caballero, FG ;
Capdevila, C ;
San Martín, D .
MATERIALS CHARACTERIZATION, 2002, 49 (02) :121-127
[12]   Site-specific quasi in situ investigation of primary static recrystallization in a low carbon steel [J].
Diehl, Martin ;
Kertsch, Lukas ;
Traka, Konstantina ;
Helm, Dirk ;
Raabe, Dierk .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2019, 755 :295-306
[13]   Grain Refinement of a Powder Nickel-Base Superalloy Using Hot Deformation and Slow-Cooling [J].
Fan, Xianqiang ;
Guo, Zhipeng ;
Wang, Xiaofeng ;
Yang, Jie ;
Zou, Jinwen .
MATERIALS, 2018, 11 (10)
[14]   Relationship between the austenite recrystallized fraction and the softening measured from the interrupted torsion test technique [J].
Fernández, AI ;
López, B ;
Rodríguez-Ibabe, JM .
SCRIPTA MATERIALIA, 1999, 40 (05) :543-549
[15]  
Gottstein G., 2009, GRAIN BOUNDARY MIGRA, DOI [10.1201/9781420054361, DOI 10.1201/9781420054361]
[16]   Microstructural variations and kinetic behaviors during metadynamic recrystallization in a nickel base superalloy with pre-precipitated δ phase [J].
He, Dao-Guang ;
Lin, Y. C. ;
Wang, Li-Hua .
MATERIALS & DESIGN, 2019, 165
[17]   A MATHEMATICAL-MODEL TO PREDICT THE MECHANICAL-PROPERTIES OF HOT ROLLED C-MN AND MICROALLOYED STEELS [J].
HODGSON, PD ;
GIBBS, RK .
ISIJ INTERNATIONAL, 1992, 32 (12) :1329-1338
[18]   Constitutive modeling of strain induced grain boundary migration via coupling crystal plasticity and phase-field methods [J].
Jafari, M. ;
Jamshidian, M. ;
Ziaei-Rad, S. ;
Raabe, D. ;
Roters, F. .
INTERNATIONAL JOURNAL OF PLASTICITY, 2017, 99 :19-42
[19]   Study on the effect of post-annealing on the microstructural evolutions and mechanical properties of rolled CGPed Aluminum-Manganese-Silicon alloy [J].
Jandaghi, Mohammad Reza ;
Pouraliakbar, Hesam .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2017, 679 :493-503
[20]   High strength and high ductility in the Co-20Cr-15W-10Ni alloy having a bimodal grain structure achieved by static recrystallization [J].
Li, Cheng-Lin ;
Park, Chan Hee ;
Choi, Seong-Woo ;
Lee, Sang-Won ;
Hong, Jae-Keun ;
Yeom, Jong-Taek .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2018, 732 :70-77
123456