Phase Evolution and Mechanical Properties of Nano-TiO2 Dispersed Zr-Based Alloys by Mechanical Alloying and Conventional Sintering

被引：11
作者：
Nuthalapati, Mohan [1 ]
Karak, S. K. [1 ]
Majumdar, J. Dutta [2 ]
Basu, A. [1 ]
机构：
[1] Natl Inst Technol, Met & Mat Engn Dept, Rourkela 769008, India
[2] Indian Inst Technol, Met & Mat Engn Dept, Kharagpur 721302, W Bengal, India
来源：
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE | 2014年 / 45A卷 / 09期
关键词：
ZIRCONIUM ALLOYS; FERRITIC STEEL; MICROSTRUCTURE; TRANSFORMATION;
D O I：
10.1007/s11661-014-2351-9
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
The present study deals with the synthesis of 1.0 to 2.0 wt pct nano-TiO2 dispersed Zr-based alloy with nominal compositions 45.0Zr-30.0Fe-20.0Ni-5.0Mo (alloy A), 44.0Zr-30.0 Fe-20.0Ni-5.0Mo-1.0TiO(2) (alloy B), 44.0Zr-30.0Fe-20.0Ni-4.5Mo-1.5TiO(2) (alloy C), and 44.0Zr-30.0Fe-20.0Ni-4.0Mo-2.0TiO(2) (alloy D) by mechanical alloying and consolidation of the milled powders using 1 GPa uniaxial pressure for 5 minutes and conventional sintering at 1673 K (1400 A degrees C). The microstructural and phase evolution during each stage of milling and the consolidated products were studied by X-ray diffraction (XRD), scanning electron microscopy and transmission electron microscopy (TEM), and energy-dispersive spectroscopy. The particle size of the milled powder was also analyzed at systemic intervals during milling, and it showed a rapid decrease in particle size in the initial hours of milling. XRD analysis showed a fine crystallite size of 10 to 20 nm after 20 hours of milling and was confirmed by TEM. The recrystallization behavior of the milled powder was studied by differential scanning calorimetry. The hardness of the sintered Zr-based alloys was recorded in the range of 5.1 to 7.0 GPa, which is much higher than that of similar alloys, developed via the melting casting route.
引用
收藏
页码：3748 / 3754
页数：7
相关论文
共 32 条
  • [1] Polymorphic phase transformation in Ti50Zr50 binary alloy by mechanical alloying
    Bera, S
    Manna, I
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2006, 417 (1-2): : 110 - 113
  • [2] Brandes E. A., 1992, SMITHELLS METALS REF, p22
  • [3] Some thoughts on the mechanisms of in-reactor corrosion of zirconium alloys
    Cox, B
    [J]. JOURNAL OF NUCLEAR MATERIALS, 2005, 336 (2-3) : 331 - 368
  • [4] USE OF THE VOIGT FUNCTION IN A SINGLE-LINE METHOD FOR THE ANALYSIS OF X-RAY-DIFFRACTION LINE BROADENING
    DEKEIJSER, TH
    LANGFORD, JI
    MITTEMEIJER, EJ
    VOGELS, ABP
    [J]. JOURNAL OF APPLIED CRYSTALLOGRAPHY, 1982, 15 (JUN) : 308 - 314
  • [5] Dieter E.G., 1928, MECH METALLURGY, P189
  • [6] GLASS-FORMING RANGES IN TRANSITION METAL-ZR ALLOYS PREPARED BY MECHANICAL ALLOYING
    ECKERT, J
    SCHULTZ, L
    URBAN, K
    [J]. JOURNAL OF THE LESS-COMMON METALS, 1988, 145 (1-2): : 283 - 291
  • [7] Effects of rare-earth elements Gd and Y on the solid solution strengthening of Mg alloys
    Gao, L.
    Chen, R. S.
    Han, E. H.
    [J]. JOURNAL OF ALLOYS AND COMPOUNDS, 2009, 481 (1-2) : 379 - 384
  • [8] Grabias A, 2008, REV ADV MATER SCI, V18, P379
  • [9] Calorimetric and structural analysis of the new phase Al33Ni16Zr51 produced by direct synthesis and mechanical alloying
    Held, O
    Braganti, JP
    Kuhnast, FA
    [J]. JOURNAL OF ALLOYS AND COMPOUNDS, 1999, 290 (1-2) : 197 - 202
  • [10] Hydrogen-induced transformation superplasticity in zirconium
    Hong, Eunji
    Dunand, David C.
    Choe, Heeman
    [J]. INTERNATIONAL JOURNAL OF HYDROGEN ENERGY, 2010, 35 (11) : 5708 - 5713
1234