Influence of process parameters on microstructural evolution and mechanical properties in friction stirred Al-2024 (T3) alloy

被引：46

作者：

Dixit, V. ^{[1
]}

Mishra, R. S. ^{[1
]}

Lederich, R. J. ^{[2
]}

Talwar, R. ^{[2
]}

机构：

[1] Missouri Univ Sci & Technol, Dept Mat Sci & Engn, Ctr Frict Sir Proc, Rolla, MO 65409 USA

[2] Boeing Phantom Works, Adv Mfg R&D, St Louis, MO 63166 USA

来源：

SCIENCE AND TECHNOLOGY OF WELDING AND JOINING | 2009年 / 14卷 / 04期

关键词：

Friction stir welding; Aluminium alloys; Differential scanning calorimetry; Precipitation evolution; Tensile strength; CU-MG ALLOYS; PRECIPITATION; HARDNESS; AA2024; WELDS;

D O I：

10.1179/136217109X415910

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Commercial Al-2024 (T3) alloy was friction stir welded at various heat index (HI) values using bead on plate approach. Quantitative analysis using electron microscopy and differential scanning calorimetry (DSC) revealed a complex variation in the precipitation evolution of Guinier-Preston-Bagaryatskii (GPB) zone and Al2CuMg (S phase) precipitates in nugget and heat affected zone (HAZ). Differential scanning calorimetry data also suggested formation energy of GPB zone equal to -236 J g(-1). Tensile properties attained a maximum for HI values close to 3.94 in the nugget region, which was attributed to corresponding minimisation of the volume fraction of coarse S phase to the profit of GPB zone. The precipitation of fine S phase precipitates resulted in higher tensile properties in HAZ as compared to those in nugget for all HI values. Experimental data were used to determine major strengthening mechanisms by using constitutive relationships.

引用

页码：346 / 355

页数：10

共 28 条

[1]

Arbegast WJ, 2003, HOT DEFORMATION OF ALUMINUM ALLOYS III, P313

[2]

ARBEGAST WJ, 2004, P SAE FRICT STIR WEL

[3] A thermodynamic assessment of the Al-Cu-Mg ternary system [J].

Buhler, T ;

Fries, SG ;

Spencer, PJ ;

Lukas, HL .

JOURNAL OF PHASE EQUILIBRIA, 1998, 19 (04) :317-333

[4] Influence of predeformation and ageing of an Al-Zn-Mg alloy - II. Modeling of precipitation kinetics and yield stress [J].

Deschamps, A ;

Brechet, Y .

ACTA MATERIALIA, 1998, 47 (01) :293-305

[5] Effect of initial temper on mechanical properties of friction stir welded Al-2024 alloy [J].

Dixit, V. ;

Mishra, R. S. ;

Lederich, R. J. ;

Talwar, R. .

SCIENCE AND TECHNOLOGY OF WELDING AND JOINING, 2007, 12 (04) :334-340

[6] Microstructure and properties of aluminum alloys friction stir welds for aircraft application [J].

Ehrström, JC ;

Bigot, A ;

Cervi, L ;

Gérard, H .

THERMEC'2003, PTS 1-5, 2003, 426-4 :2941-2946

[7] Quantitative investigation of precipitation and mechanical behaviour for AA2024 friction stir welds [J].

Genevois, C ;

Deschamps, A ;

Denquin, A ;

Doisneau-cottignies, B .

ACTA MATERIALIA, 2005, 53 (08) :2447-2458

[8] Thermomechanical conditions and resultant microstructures in friction stir welded 2024 aluminum [J].

Heurtier, P ;

Jones, MJ ;

Desrayaud, C ;

Driver, JH ;

Montheillet, F .

THERMEC'2003, PTS 1-5, 2003, 426-4 :2927-2932

[9] Correlation between microstructure and microhardness in a friction stir welded 2024 aluminium alloy [J].

Jones, MJ ;

Heurtier, P ;

Desrayaud, C ;

Montheillet, F ;

Allehaux, D ;

Driver, JH .

SCRIPTA MATERIALIA, 2005, 52 (08) :693-697

[10] SEM-EBSD characterisation of the deformation microstructure in friction stir welded 2024 T351 aluminium alloy [J].

Karlsen, M ;

Frigaard, O ;

Hjelen, J ;

Grong, O ;

Norum, H .

THERMEC'2003, PTS 1-5, 2003, 426-4 :2861-2866

← 1 2 3 →