Heat transfer characteristics of a micro-scale impinging slot jet

被引:47
作者
Choo, Kyo Sung [1 ]
Youn, Young Jik [1 ]
Kim, Sung Jin [1 ]
Lee, Dae Hee [2 ]
机构
[1] Korea Adv Inst Sci & Technol, Sch Mech Aerosp & Syst Engn, Taejon 305701, South Korea
[2] Inje Univ, Sch Mech & Automot Engn, High Safety Vehicle Core Technol Res Ctr, Gimhae 621749, South Korea
基金
新加坡国家研究基金会;
关键词
AIR-JET; GAS;
D O I
10.1016/j.ijheatmasstransfer.2009.02.015
中图分类号
O414.1 [热力学];
学科分类号
摘要
In the present study, heat transfer characteristics of a micro-scale slot jet impinging on a heated flat plate are experimentally investigated. The effects of Reynolds numbers (Re = 150-5000) and nozzle-to-plate spacings (Z/d(h) = 0.5-10) on the Nusselt number are considered. Based on the experimental results, correlations on the stagnant and average Nusselt numbers for the micro-scale impinging slot jet are developed as a function of Reynolds number and nozzle-to-plate spacing. At Reynolds numbers (Re < 2500), different from the existing results, the present study shows that the heat transfer characteristics of the microscale impinging slot jet are similar to those of the macro-scale impinging slot jet. However, at Reynolds numbers (Re >= 2500), the present study shows that the heat transfer characteristics of the micro-scale impinging slot jet are different from those of the macro-scale impinging slot jet. Firstly, a maximum local Nusselt number occurs at a shifted peak of about x/d(h) = 1.75 under the condition of large nozzle-to-plate spacing (Z/d(h) > 1), rather than at the stagnation point. Secondly, the effect of the nozzle-to-plate spacing on the Nusselt number is significant. The exponent on Reynolds number is the function of nozzle-to-plate spacing Nu proportional to Re-f(Z/dh), rather than a constant value. Crown Copyright (C) 2009 Published by Elsevier Ltd. All rights reserved.
引用
收藏
页码:3169 / 3175
页数:7
相关论文
共 17 条
[1]   HEAT TRANSFER CHARACTERISTICS OF IMPINGING 2-DIMENSIONAL AIR JETS [J].
GARDON, R ;
AKFIRAT, JC .
JOURNAL OF HEAT TRANSFER, 1966, 88 (01) :101-&
[2]  
Gardon R., 1965, INT J HEAT MASS TRAN, V8, P1261
[3]   STREAMWISE DISTRIBUTION OF THE RECOVERY FACTOR AND THE LOCAL HEAT-TRANSFER COEFFICIENT TO AN IMPINGING CIRCULAR AIR-JET [J].
GOLDSTEIN, RJ ;
BEHBAHANI, AI ;
HEPPELMANN, KK .
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 1986, 29 (08) :1227-1235
[4]  
Incropera FrankP., 2002, INTRO HEAT TRANSFER, V4th
[5]  
Kline S.J., 1952, ASME Mechanical Engineering, V75, P3, DOI DOI 10.1016/J.CHAOS.2005.11.046
[6]   Turbulent flow and heat transfer measurements on a curved surface with a fully developed round impinging jet [J].
Lee, DH ;
Chung, YS ;
Kim, DS .
INTERNATIONAL JOURNAL OF HEAT AND FLUID FLOW, 1997, 18 (01) :160-169
[7]   Application of pressure and temperature sensitive paints for study of heat transfer to a circular impinging air jet [J].
Liu, Quan ;
Sleiti, A. K. ;
Kapat, J. S. .
INTERNATIONAL JOURNAL OF THERMAL SCIENCES, 2008, 47 (06) :749-757
[8]   AIR-JET IMPINGEMENT HEAT-TRANSFER AT LOW NOZZLE PLATE SPACINGS [J].
LYTLE, D ;
WEBB, BW .
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 1994, 37 (12) :1687-1697
[9]  
Martin H., 1977, ADV HEAT TRANSFER, V13, P1
[10]   Spatially resolved heat transfer rates in an impinging circular microscale jet [J].
Patil, VA ;
Narayanan, V .
MICROSCALE THERMOPHYSICAL ENGINEERING, 2005, 9 (02) :183-197