Effect of grain size reduction of AA2124 aluminum alloy powder compacted by spark plasma sintering

被引：49

作者：

Eldesouky, A. ^{[1
]}

Johnsson, M. ^{[2
]}

Svengren, H. ^{[2
]}

Attallah, M. M. ^{[3
]}

Salem, H. G. ^{[4
]}

机构：

[1] Egypt Japan Univ Sci & Technol, Dept Mat Sci & Engn, Alexandria, Egypt

[2] Stockholm Univ, Dept Mat & Environm Chem, S-10691 Stockholm, Sweden

[3] Univ Birmingham, IRC Mat Proc Sch Met & Mat, Edgbaston, England

[4] Amer Univ Cairo, Dept Mech Engn, Cairo, Egypt

来源：

JOURNAL OF ALLOYS AND COMPOUNDS | 2014年 / 609卷

关键词：

AA2124; Nano-powder; Mechanical milling; Spark plasma sintering; BEHAVIOR; COMPOSITES;

D O I：

10.1016/j.jallcom.2014.04.136

中图分类号：

O64 [物理化学（理论化学）、化学物理学];

学科分类号：

070304 ; 081704 ;

摘要：

Nanocrystalline (Average grain size similar to 200 nm) bulk AA2124 alloy was produced through high energy ball milling of microcrystalline powder followed by spark plasma sintering (SPS) at 480 degrees C with a holding time of 10 min. The effect of initial particle and grain size on the microstructural evolution as well as on the relative density and mechanical properties of the specimens consolidated through SPS and hot pressing (HP) at the same temperature for 60 min was investigated for ball milled nano-powders (NP), as well as as-received micro-powders (MP). Results showed that the NP specimens consolidated with SPS had the highest microhardness values compared to the other specimens despite not achieving full densification. On the other hand, a general increase in density, hardness, and compressive strength was observed for all SPS consolidates compared to HP. The presence of aluminum oxide and its influence on the consolidation process as well as the resulting mechanical properties of the bulk specimens is also discussed. (C) 2014 The Authors. Published by Elsevier B.V.

引用

页码：215 / 221

页数：7

共 19 条

[1] Microstructure and mechanical behavior of nanocrystalline metals [J].

Agnew, SR ;

Elliott, BR ;

Youngdahl, CJ ;

Hemker, KJ ;

Weertman, JR .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2000, 285 (1-2) :391-396

[2] Effect of spark plasma sintering temperature on microstructure and mechanical properties of melt-spun TiAl alloys [J].

Chai Li-hua ;

Chen Yu-yong ;

Zhang Lai-qi ;

Lin Jun-pin .

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, 2012, 22 (03) :528-533

[3] High strength nanocrystalline cobalt with high tensile ductility [J].

Karimpoor, AA ;

Erb, U ;

Aust, KT ;

Palumbo, G .

SCRIPTA MATERIALIA, 2003, 49 (07) :651-656

[4] Electrochemical Corrosion Behavior of Nanocrystalline Materials-a Review [J].

Liu, Li ;

Li, Ying ;

Wang, Fuhui .

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2010, 26 (01) :1-14

[5] Formation of micron-sized and nanometer-sized single crystal alumina whiskers by displacement reactions [J].

Ng, DHL ;

Yu, P ;

Ma, NG ;

Lo, CK ;

Kwok, WY ;

Yau, MY ;

To, CY ;

Li, TK ;

Deng, CJ .

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY, 2006, 26 (09) :1561-1565

[6]

Padilla HA, 2010, EXP MECH, V50, P5, DOI [10.1007/s11340-009-9301-2, 10.1007/s11340-009-9301]

[7]

Qi Z.Q., 1 INT M DEV MAT PROC, P4227

[8] The effect of hot isostatic pressing on the microstructure and tensile properties of an unmodified A356-T6 cast aluminum alloy [J].

Ran, Guang ;

Zhou, Jingen ;

Wang, Q. G. .

JOURNAL OF ALLOYS AND COMPOUNDS, 2006, 421 (1-2) :80-86

[9] Microstructure and mechanical properties of nanocrystalline high strength Al-Mg-Si (AA6061) alloy by high energy ball milling and spark plasma sintering [J].

Rana, Jatinkumar Kumar ;

Sivaprahasam, D. ;

Raju, K. Seetharama ;

Sarma, V. Subramanya .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2009, 527 (1-2) :292-296

[10]

Randall M., 1996, German: Sintering: Theory and Practice

← 1 2 →