Effect of weld zone and corner with cold bending effect on wrinkling of rectangular welded tube in rotary draw bending

被引:10
作者
Liu, Hailong [1 ,2 ]
Liu, Yuli [1 ,2 ]
Zhang, Peng [2 ]
Du, Xiaoyu [2 ]
机构
[1] Northwestern Polytech Univ Shenzhen, Res & Dev Inst, Shenzhen 518057, Peoples R China
[2] Northwestern Polytech Univ, Sch Mat Sci & Engn, State Key Lab Solidificat Proc, Xian 710072, Peoples R China
关键词
Thin-walled rectangular welded tube; Weld zone; Corner with cold bending effect; Rotary draw bending; Wrinkling of inner flange and side wall;
D O I
10.1016/j.tws.2020.107115
中图分类号
TU [建筑科学];
学科分类号
0813 ;
摘要
Wrinkling of QSTE700 high strength steel thin-walled rectangular welded tube is easy to occur in rotary draw bending (RDB) process due to the existence of non-homogeneous weld zone and corner with cold bending effect. So the FE model of RDB of QSTE700 rectangular welded tube considering weld zone and corner with cold bending effect was established. Based on this FE model, the effect of weld zone and corner with cold bending effect on wrinkling of inner flange and side wall of rectangular welded tube in RDB was researched. The results showed that: when weld zone and corner with cold bending effect were studied separately, weld zone both increased the wrinkling height of inner flange and side wall. However, the influence of corner with cold bending effect on wrinkling height of side wall and inner flange was inconsistent, it reduced the wrinkling height of inner flange, but increased the wrinkling height of side wall. When the weld zone and corner interacted, the coupling effect between weld zone and corner with cold bending effect on wrinkling resulted in the decrease of wrinkling height of inner flange and increase of wrinkling height of side wall of rectangular welded tube in RDB.
引用
收藏
页数:10
相关论文
共 50 条
[21]   Dynamic detection of instability defects in tube rotary draw bending [J].
Simonetto, Enrico ;
Ghiotti, Andrea ;
Bruschi, Stefania ;
Gemignani, Roberto .
45TH SME NORTH AMERICAN MANUFACTURING RESEARCH CONFERENCE (NAMRC 45), 2017, 10 :319-328
[22]   In-process measurement of springback in tube rotary draw bending [J].
Enrico Simonetto ;
Andrea Ghiotti ;
Stefania Bruschi .
The International Journal of Advanced Manufacturing Technology, 2021, 112 :2485-2496
[23]   Numerical research on high-strength rectangular section steel tube in rotary-draw bending [J].
Lei, C. (chxlei@hit.edu.cn), 1600, Trans Tech Publications Ltd (620) :417-423
[24]   Study on cross-sectional deformation of rectangular waveguide tube with different materials in rotary draw bending [J].
Zhan, Hong ;
Liu, Yuli ;
Zhang, Honglie .
JOURNAL OF MATERIALS RESEARCH, 2017, 32 (20) :3912-3920
[25]   Study on the influence of mandrel type on copper tube rotary draw bending [J].
Peng, Yinghong ;
Tang, Ding ;
Li, Dayong .
INTERNATIONAL JOURNAL OF MATERIALS & PRODUCT TECHNOLOGY, 2008, 32 (04) :406-422
[26]   The effect of aging heat treatment on the formability and microstructure of the AA6063 tube in the rotary draw bending process [J].
Elyasi, Majid ;
Talebi-Ghadikolaee, Hossein ;
Zeinolabedin-Beygi, Ali ;
Modanloo, Vahid ;
Khatir, Farzad Ahmadi .
JOURNAL OF ENGINEERING RESEARCH, 2025, 13 (01) :283-293
[27]   Experimental Research on Strain Distribution Characteristics of Thin-walled Rectangular Tube in Rotary-draw Bending [J].
Tian, Shan ;
Liu, Yuli ;
Zhao, Gangyao ;
Yang, He .
MANUFACTURING ENGINEERING AND AUTOMATION I, PTS 1-3, 2011, 139-141 :502-505
[28]   Plastic Deformation Characteristics Analysis in Rotary-draw Bending Process of Thin-walled Rectangular Tube [J].
Zhao, G. Y. ;
Liu, Y. L. ;
Yang, H. .
MANUFACTURING SCIENCE AND ENGINEERING, PTS 1-5, 2010, 97-101 :320-323
[29]   Effect of the internal pressure in the rubber mandrel on the defects of the rotary draw bending process [J].
Majid Elyasi .
Journal of Mechanical Science and Technology, 2024, 38 :1149-1153
[30]   Rotary draw bending of rectangular tubes using a novel parallelepiped elastic mandrel [J].
S. Ancellotti ;
M. Benedetti ;
V. Fontanari ;
S. Slaghenaufi ;
M. Tassan .
The International Journal of Advanced Manufacturing Technology, 2016, 85 :1089-1103