Novel design optimization for passive cooling PCM assisted battery thermal management system in electric vehicles

被引：57
作者：
Youssef, Rekabra [1 ,2 ,3 ]
Hosen, Md Sazzad [1 ,2 ]
He, Jiacheng [1 ,2 ]
AL-Saadi, Mohammed [1 ,2 ,3 ]
Van Mierlo, Joeri [1 ,2 ,3 ]
Berecibar, Maitane [1 ,2 ]
机构：
[1] Vrije Univ Brussel, ETEC Dept, Brussels, Belgium
[2] Vrije Univ Brussel, MOBI Res Grp, Brussels, Belgium
[3] Flanders Make, B-3001 Heverlee, Belgium
来源：
CASE STUDIES IN THERMAL ENGINEERING | 2022年 / 32卷
基金：
欧盟地平线“2020”;
关键词：
Jute; Thermal management; Passive cooling; Phase change material PCM; Lithium-ion battery; Electric vehicles; LITHIUM-ION BATTERY; PHASE-CHANGE MATERIALS; POROUS METAL FOAM; PERFORMANCE; PACK; COMPOSITE; CONDUCTIVITY; IMPACT; MODEL;
D O I：
10.1016/j.csite.2022.101896
中图分类号：
O414.1 [热力学];
学科分类号：
摘要：
Recently, the phase change material (PCM) battery thermal management system (BTMS) attracted attention. However, enhancement and optimization for the BTMS are required due to volumetric system design and low thermal conductivity. This study provides a novel design optimization to improve the environmental aspect of the cooling system and reduce its weight. Jute fibers as a planet-system, available, cheap, and weightless material is combined with the PCM battery thermal management based. The thermal behavior of large lithium-ion batteries (LIB) under different load protocols including fast discharge, periodic load, and real drive cycle are investigated. The results with the periodic load profile confirm that the maximum temperature for the cooling strategies of no-cooling, PCM cooling and PCM with jute reaches 39.22 degrees C, 38.22 degrees C and 35.09 degrees C, respectively. Moreover, applying aggressive high constant discharge current leads to further reduction in maximum temperature, where the maximum temperature reaches 47.27 degrees C, 41.06 degrees C, and 36.29 degrees C with the no-cooling, PCM cooling and PCM with jute cooling strategies, respectively. This article represents the first attempt to use a combination of jute and PCM in order to maximize temperature efficiency enhanced. Thus, this research contributes to further design optimization in battery thermal management system simplicity, environmental friendliness, energy and weight saving.
引用
收藏
页数：10
相关论文
共 49 条
[1]   Evaluation of the performance of local fibers in evaporative cooling [J].
Al-Suliman, F .
ENERGY CONVERSION AND MANAGEMENT, 2002, 43 (16) :2267-2273
[2]   Thermal management of a LiFePO4 battery pack at high temperature environment using a composite of phase change materials and aluminum wire mesh plates [J].
Azizi, Y. ;
Sadrameli, S. M. .
ENERGY CONVERSION AND MANAGEMENT, 2016, 128 :294-302
[3]   Thermal management of a Li-ion battery using carbon fiber-PCM composites [J].
Babapoor, A. ;
Azizi, M. ;
Karimi, G. .
APPLIED THERMAL ENGINEERING, 2015, 82 :281-290
[4]   Comprehensive Passive Thermal Management Systems for Electric Vehicles [J].
Behi, Hamidreza ;
Karimi, Danial ;
Youssef, Rekabra ;
Suresh Patil, Mahesh ;
Van Mierlo, Joeri ;
Berecibar, Maitane .
ENERGIES, 2021, 14 (13)
[5]  
Brend D.E.C, LEATHERWORK STRUCTUR, P43
[6]   The state of the art of electric and hybrid vehicles [J].
Chan, CC .
PROCEEDINGS OF THE IEEE, 2002, 90 (02) :247-275
[7]  
Chattopadhyay D., VIEW PROJECT IMPARTI
[8]   Melting and solidification of PCM embedded in porous metal foam in horizontal multi-tube heat storage system [J].
Esapour, Mehdi ;
Hamzehnezhad, Arash ;
Darzi, A. Ali Rabienataj ;
Jourabian, Mahmoud .
ENERGY CONVERSION AND MANAGEMENT, 2018, 171 :398-410
[9]   Thermal runaway mechanism of lithium ion battery for electric vehicles: A review [J].
Feng, Xuning ;
Ouyang, Minggao ;
Liu, Xiang ;
Lu, Languang ;
Xia, Yong ;
He, Xiangming .
ENERGY STORAGE MATERIALS, 2018, 10 :246-267
[10]   A novel methodology to determine the specific heat capacity of lithium-ion batteries [J].
He, Jiacheng ;
Youssef, Rekabra ;
Hosen, Md Sazzad ;
Akbarzadeh, Mohsen ;
Van Mierlo, Joeri ;
Berecibar, Maitane .
JOURNAL OF POWER SOURCES, 2022, 520
12345