Surface softening and hardening of WC-Co using pulsed laser irradiation

被引：16

作者：

Kano, S. ^{[1
]}

Inoue, T. ^{[1
]}

机构：

[1] Natl Inst Adv Ind Sci & Technol, AIST, Tsukuba, Ibaraki 3058564, Japan

来源：

SURFACE & COATINGS TECHNOLOGY | 2006年 / 201卷 / 1-2期

关键词：

WC-Co; softening; hardening; pulsed laser; surface analysis;

D O I：

10.1016/j.surfcoat.2005.11.126

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

The surface of cobalt-containing tungsten-carbide was treated using a pulsed Nd: YAG laser beam under atmospheric conditions in order to control its surface hardness by means of surface diffusion or concentration of cobalt. Elemental analyses of the treated surfaces revealed a laser fluence of 0.25 J/cm(2) to be the most suitable condition for the concentration of cobalt and the removal of surface contaminants, such as hydrocarbons and oxygen gas, without damaging the surface. At this laser fluence, the concentration of cobalt was reduced close to the center of irradiation but increased in the area surrounding the irradiation center. This concentration of cobalt resulted in a softening of the WC-Co surface by over 10% compared to the non-treated surface, as measured by a Knoop hardness tester under a load of 9.8 X 10(-2) N. (c) 2005 Elsevier B.V. All rights reserved.

引用

页码：223 / 229

页数：7

共 50 条

[31] Effect of Laser Surface Hardening on the Microstructure, Hardness, Wear Resistance and Softening of a Low Carbon Steel
Zhang, P-L.
Yan, H.
Xu, P-Q.
Yu, Z-S.
Li, C-G.
Lu, Q-H.
LASERS IN ENGINEERING, 2014, 28 (3-4) : 135 - 149
[32] Physical and Mechanical Properties of WC-Co Submicron Powders using P/M Technique
Mahaidin, Ahmed Aswad
Selamat, Mohd Asri
Manaf, Samsiah Abdul
Jaafar, Talib Ria
ADVANCED MATERIALS CONFERENCE (AMC 2012), 2014, 879 : 12 - 15
[33] A comparison of the DPSS UV laser ablation characteristic of 1024 and H10F WC-Co
See, Tian Long
Chantzis, Dimitrios
Royer, Raphael
Metsios, Ioannis
Antar, Mohammad
Marimuthu, Sundar
OPTICS AND LASER TECHNOLOGY, 2017, 92 : 101 - 108
[34] Effect of Ti addition on microstructure and corrosion properties of laser cladded WC-Co/NiCrBSi(Ti) coatings
Hulka, I.
Utu, D.
Serban, V. A.
Negrea, P.
Lukac, F.
Chraska, T.
APPLIED SURFACE SCIENCE, 2020, 504
[35] The using of laser radiation at surface hardening of improvement steels
Zara, A.
Stoicanescu, M.
Giacomelli, I.
Cazacu, M.
JOURNAL OF OPTOELECTRONICS AND ADVANCED MATERIALS, 2013, 15 (9-10): : 1084 - 1089
[36] Effects of binder concentration on the nanometric surface characteristics of WC-Co materials in ultra-precision grinding
Zhang, Quanli
Guo, Nan
Chen, Yan
To, Suet
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS, 2019, 85
[37] Surface roughness characterization of thermally sprayed and precision machined WC-Co and Alloy-625 coatings
Zhong, Z. W.
Peng, Z. F.
Liu, N.
MATERIALS CHARACTERIZATION, 2007, 58 (10) : 997 - 1005
[38] Surface structuring of titanium under pulsed Nd:YAG laser irradiation
György, E
del Pino, AP
Serra, P
Morenza, JL
ROMOPTO 2003: SEVENTH CONFERENCE ON OPTICS, 2004, 5581 : 323 - 332
[39] Optimization and erosion wear response of NiCrSiB/WC-Co HVOF coating using Taguchi method
Praveen, Ayyappan Susila
Sarangan, J.
Suresh, S.
Channabasappa, B. H.
CERAMICS INTERNATIONAL, 2016, 42 (01) : 1094 - 1104
[40] Small scale testing of PCD and WC-Co tooling in rock cutting using longitudinal turning
Johansson, Daniel
Hrechuk, Andrew
Bushlya, Volodymyr
Martensson, Malin
Can, Antionette
Stahl, Jan-Eric
WEAR, 2019, 426 : 1515 - 1522

← 1 2 3 4 5 →