Microstructures and mechanical properties of Nbss/Nb5Si3 in-situ composite prepared by electromagnetic cold crucible directional solidification

被引：30

作者：

Kang, Yongwang ^{[1
]}

Yan, Yuncheng ^{[1
,2
]}

Song, Jinxia ^{[1
]}

Ding, Hongsheng ^{[2
]}

机构：

[1] Beijing Inst Aeronaut Mat, Sci & Technol Adv High Temp Struct Mat Lab, Beijing 100095, Peoples R China

[2] Harbin Inst Technol, Natl Key Lab Precis Hot Proc Met, Harbin 150001, Peoples R China

来源：

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2014年 / 599卷

关键词：

Intermetallics; Microanalysis; Mechanical characterization; FRACTURE-TOUGHNESS; POWDER COMPACTS; SYSTEM; AL;

D O I：

10.1016/j.msea.2014.01.077

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

The Nb-ss/Nb5Si3 in-situ composite with the nominal composition of Nb-24Ti-12Si-4Cr-4Al-2Hf (at%) has been successfully fabricated by electromagnetic cold crucible directional solidification. Microstructures of the initial transition (IT) zone and the steady-state growth (SSG) region were observed by scanning electron microscope, and their phase compositions were analyzed with X-ray diffraction (XRD). The room temperature fracture toughness and the tensile strength at 1250 degrees C were measured. The results indicated that from IT zone to SSG zone, the major silicide transferred from gamma-(Nb,Ti)(5)Si-3 to beta-(Nb,Ti)(5)Si-3. The directional solidification microstructure with coupled Nb-ss and Nb5Si3 was created in SSG region. Compared SSG region with IT zone, the room temperature fracture toughness and the high temperature tensile strength increased about 50% and 24%, respectively, which was contributed to the directional solidification microstructure and the type transformation of silicide. (C) 2014 Elsevier ay. All rights reserved.

引用

页码：87 / 91

页数：5

共 30 条

[1]

[Anonymous], E128008A ASTM

[2] The balance of mechanical and environmental properties of a multielement niobium-niobium silicide-based in situ composite [J].

Bewlay, BP ;

Jackson, MR ;

Lipsitt, HA .

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1996, 27 (12) :3801-3808

[3] Ultrahigh-temperature Nb-silicide-based composites [J].

Bewlay, BP ;

Jackson, MR ;

Zhao, JC ;

Subramanian, PR ;

Mendiratta, MG ;

Lewandowski, JJ .

MRS BULLETIN, 2003, 28 (09) :646-653

[4] A review of very-high-temperature Nb-silicide-based composites [J].

Bewlay, BP ;

Jackson, MR ;

Zhao, JC ;

Subramanian, PR .

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2003, 34A (10) :2043-2052

[5] The Nb-Ti-Si ternary phase diagram: Determination of solid-state phase equilibria in Nb- and Ti-rich alloys [J].

Bewlay, BP ;

Jackson, MR ;

Bishop, RR .

JOURNAL OF PHASE EQUILIBRIA, 1998, 19 (06) :577-586

[6] Effect of Mo on microstructure and mechanical behaviour of as-cast NbSS-Nb5Si3 in situ composites [J].

Chattopadhyay, K. ;

Balachandran, G. ;

Mitra, R. ;

Ray, K. K. .

INTERMETALLICS, 2006, 14 (12) :1452-1460

[7]

Dehoff RR, 2003, MATER RES SOC SYMP P, V753, P77

[8] The manufacture of a niobium/niobium-silicide-based alloy using direct laser fabrication [J].

Dicks, Robert ;

Wang, Fude ;

Wu, Xinhua .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2009, 209 (04) :1752-1757

[9] Influence of oxygen on microstructure and mechanical properties of directionally solidified Ti-47Al-2Cr-2Nb alloy [J].

Ding, Hongsheng ;

Nie, Ge ;

Chen, Ruirun ;

Guo, Jingjie ;

Fu, Hengzhi .

MATERIALS & DESIGN, 2012, 41 :108-113

[10] Study of the role of Al, Cr and Ti additions in the microstructure of Nb-18Si-5Hf base alloys [J].

Grammenos, I. ;

Tsakiropoulos, P. .

INTERMETALLICS, 2010, 18 (02) :242-253

← 1 2 3 →