Thermo-ecological cost assessment and optimization for a hybrid combined cooling, heating and power system coupled with compound parabolic concentrated-photovoltaic thermal solar collectors

被引:50
作者
Chen, Yuzhu [1 ]
Wang, Jiangjiang [1 ]
Ma, Chaofan [1 ]
Gao, Yuefen [1 ]
机构
[1] North China Elect Power Univ, Sch Energy Power & Mech Engn, Baoding 071003, Hebei, Peoples R China
基金
中国国家自然科学基金;
关键词
Combined cooling heating and power (CCHP) system; Compound parabolic concentrated; Photovoltaic thermal solar collector; Thermo-ecological cost; Optimization; LIFE-CYCLE ASSESSMENT; AIR ENERGY-STORAGE; PERFORMANCE ANALYSIS; CCHP SYSTEM; EXERGY ANALYSIS; BIOMASS; SIMULATION; DESIGN; PVT; ELECTRICITY;
D O I
10.1016/j.energy.2019.03.185
中图分类号
O414.1 [热力学];
学科分类号
摘要
The aim of this work is to optimize and minimize the thermo-ecological cost (TEC) of a novel hybrid combined cooling heating and power (CCHP) system integrated with solar energy. A basic natural gas CCHP system based on internal combustion engine (ICE) is coupled with compound parabolic concentrated-photovoltaic thermal (CPC-PVT) collectors to construct a novel hybrid CCHP system. To minimize the TEC, an optimization methodology was proposed to optimize the configurations and installations of ICE and CPC-PVT, as well as the operation strategies. The TECs of multi-products of the CCHP system were assessed and compared in the following electrical load (FEL) and following thermal load (FTL) modes. The impacts of key parameters on TEC were analyzed and discussed. The results of a case study indicated that the system integrated with 100% photovoltaic covered ratio and 400 kW ICE gets the lowest TEC of 2.36 J/J in the FTL mode. The TECs of electricity decline 28.8% and 17.0% in the FEL and en. modes, respectively when the photovoltaic covered ratio increases from 0 to 1.0. The increasing heat storage ratio leads to the increase of TEC of heat exergy carried by water due to the heat loss. (C) 2019 Elsevier Ltd. All rights reserved.
引用
收藏
页码:479 / 492
页数:14
相关论文
共 50 条
[1]   Performance assessment of a novel system using parabolic trough solar collectors for combined cooling, heating, and power production [J].
Al-Sulaiman, Fahad A. ;
Hamdullahpur, Feridun ;
Dincer, Ibrahim .
RENEWABLE ENERGY, 2012, 48 :161-172
[2]   Monthly assessments of exergetic, economic and environmental criteria optimization of a solar micro-CCHP based on DORC [J].
Boyaghchi, Fateme Ahmadi ;
Chavoshi, Mansoure .
SOLAR ENERGY, 2018, 166 :351-370
[3]   A novel renewable polygeneration system for hospital buildings: Design, simulation and thermo-economic optimization [J].
Buonomano, Annamaria ;
Calise, Francesco ;
Ferruzzi, Gabriele ;
Vanoli, Laura .
APPLIED THERMAL ENGINEERING, 2014, 67 (1-2) :43-60
[4]   Design and simulation of a prototype of a small-scale solar CHP system based on evacuated flat-plate solar collectors and Organic Rankine Cycle [J].
Calise, Francesco ;
d'Accadia, Massimo Dentice ;
Vicidomini, Maria ;
Scarpellino, Marco .
ENERGY CONVERSION AND MANAGEMENT, 2015, 90 :347-363
[5]   Dynamic simulation of a novel high-temperature solar trigeneration system based on concentrating photovoltaic/thermal collectors [J].
Calise, Francesco ;
d'Accadia, Massimo Dentice ;
Palombo, Adolfo ;
Vanoli, Laura .
ENERGY, 2013, 61 :72-86
[6]   Thermal modeling of a trigeneration system based on beta-type Stirling engine for reductions of fuel consumption and pollutant emission [J].
Chahartaghi, Mahmood ;
Sheykhi, Mohammad .
JOURNAL OF CLEANER PRODUCTION, 2018, 205 :145-162
[7]   Numerical simulation and experimental analysis of an LCPV/T system under real operating conditions [J].
Chen Haiping ;
Liu Haowen ;
Zhang Heng ;
Liang Kai ;
Guo Xinxin ;
Yang Boran .
JOURNAL OF CLEANER PRODUCTION, 2019, 209 :903-915
[8]  
Cuadra C.T., 2009, THER ANAL MODEL SIMU, V2, P61
[9]  
Jan Szargut, 2005, EXERGY METHOD TECHNI, V18
[10]   Thermo-economic assessment and application of CCHP system with dehumidification and hybrid refrigeration [J].
Jiang, Runhua ;
Qin, Frank G. F. ;
Yin, Huibin ;
Yang, Minlin ;
Xu, Yongjun .
APPLIED THERMAL ENGINEERING, 2017, 125 :928-936