High energy flux thermo-mechanical test of 1D-carbon-carbon fibre composite prototypes for the SPIDER diagnostic calorimeter

被引：5

作者：

De Muri, M. ^{[1
]}

Cavallin, T. ^{[2
]}

Pasqualotto, R. ^{[1
]}

Dalla Palma, M. ^{[1
]}

Cervaro, V. ^{[1
]}

Fasolo, D. ^{[1
]}

Franchin, L. ^{[1
]}

Tollin, M. ^{[1
]}

Greuner, H. ^{[3
]}

Boeswirth, B. ^{[3
]}

Serianni, G. ^{[1
]}

机构：

[1] Euratom ENEA Assoc, Consorzio RFX, I-35127 Padua, Italy

[2] Ist Energet & Interfasi, I-35127 Padua, Italy

[3] Max Planck Inst Plasma Phys, D-85748 Garching, Germany

来源：

REVIEW OF SCIENTIFIC INSTRUMENTS | 2014年 / 85卷 / 02期

关键词：

D O I：

10.1063/1.4827655

中图分类号：

TH7 [仪器、仪表];

学科分类号：

0804 ; 080401 ; 081102 ;

摘要：

Operation of the thermonuclear fusion experiment ITER requires additional heating via injection of neutral beams from accelerated negative ions. In the SPIDER test facility, under construction in Padova, the production of negative ions will be studied and optimised. STRIKE (Short-Time Retractable Instrumented Kalorimeter Experiment) is a diagnostic used to characterise the SPIDER beam during short pulse operation (several seconds) to verify if the beam meets the ITER requirements about the maximum allowed beam non-uniformity (below +/- 10%). The major components of STRIKE are 16 1D-CFC (Carbon-Carbon Fibre Composite) tiles, observed at the rear side by a thermal camera. This contribution gives an overview of some tests under high energy particle flux, aimed at verifying the thermo-mechanical behaviour of several CFC prototype tiles. The tests were performed in the GLADIS facility at IPP (Max-Plank-Institut fur Plasmaphysik), Garching. Dedicated linear and nonlinear simulations were carried out to interpret the experiments and a comparison of the experimental data with the simulation results is presented. The results of some morphological and structural studies on the material after exposure to the GLADIS beam are also given.

引用

页数：3

共 6 条

[1] Ciric D., 1994, FUSION TECHNOL JET, V059, P25
[2] Characterization, test and interpretative simulations of one-dimensional Carbon Fiber Composite prototype for SPIDER experiment
De Muri, M.
Cervaro, V.
Dal Bello, S.
Dalla Palma, M.
Fasolo, D.
Franchin, L.
Pasqualotto, R.
Pomaro, N.
Rizzolo, A.
Tollin, M.
Serianni, G.
[J]. FUSION ENGINEERING AND DESIGN, 2013, 88 (9-10) : 1758 - 1763
[3] Diefendorf R. J., 1988, ENG MAT HDB ASM INT
[4] High heat flux facility GLADIS: Operational characteristics and results of W7-X pre-series target tests
Greuner, H.
Boeswirth, B.
Boscary, J.
McNeely, P.
[J]. JOURNAL OF NUCLEAR MATERIALS, 2007, 367 (SPEC. ISS.) : 1444 - 1448
[5] Design and analyses of a one-dimensional CFC calorimeter for SPIDER beam characterisation
Rizzolo, Andrea
Dalla Palma, Mauro
De Muri, Michela
Serianni, Gianluigi
[J]. FUSION ENGINEERING AND DESIGN, 2010, 85 (10-12) : 2268 - 2273
[6] The ITER full size plasma source device design
Sonato, P.
Agostinetti, P.
Anaclerio, G.
Antoni, V.
Barana, O.
Bigi, M.
Boldrin, M.
Cavenago, M.
Dal Bello, S.
Dalla Palma, M.
Daniele, A.
D'Arienzo, M.
De Lorenzi, A.
Ferro, A.
Fiorentin, A.
Gaio, E.
Gazza, E.
Grando, L.
Fantini, F.
Fellin, F.
Luchetta, A.
Manduchi, G.
Milani, F.
Marcuzzi, D.
Novello, L.
Pasqualotto, R.
Pavei, M.
Pengo, R.
Peruzzo, S.
Pesce, A.
Pilan, N.
Piovan, R.
Pomaro, N.
Recchia, M.
Rigato, W.
Rizzolo, A.
Serianni, G.
Spolaore, M.
Spolaore, P.
Sandri, S.
Taliercio, C.
Toigo, V.
Valisa, M.
Veltri, P.
Zaccaria, R.
Zamengo, A.
Zanotto, L.
[J]. FUSION ENGINEERING AND DESIGN, 2009, 84 (2-6) : 269 - 274

← 1 →