Improving the Strength of Friction-Stir-Welded Joints of AA1100 Alloy

被引：9
作者：
Senapati, N. Pallavi [1 ]
Bhoi, R. K. [1 ]
机构：
[1] SOA Univ, ITER, Dept Mech Engn, Bhubaneswar 751030, India
来源：
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE | 2021年 / 30卷 / 01期
关键词：
friction stir welding; grain size; phase analysis; residual stress; ultimate tensile strength; x-ray diffraction; RESIDUAL-STRESS DISTRIBUTIONS; ALUMINUM-ALLOY; MECHANICAL-PROPERTIES; TEMPERATURE DISTRIBUTION; MICROSTRUCTURE; AA5083-AA6082;
D O I：
10.1007/s11665-020-05331-6
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
This paper deals with the experimental analysis of Friction Stir Welding (FSW) of AA1100 aluminum alloy joined by means of a square pin tool. During the process, temperature measurement has been done by means of K-type thermocouples and it has been noticed that the temperature in the advancing side (AS) of the weld is about 20-25 degrees C higher than its retreating side (RS). The ultimate tensile strength (UTS) of the welded specimen is increased by 20% of the parent material due to the uniform dispersion of silicon particles present within the base material. Microstructural observations revealed finely arranged equiaxed grains in the nugget region of the weld. X-ray diffraction results showed the formation of alumina (Al2O3) in the weld nugget due to high heat generation and exposure to atmospheric oxygen during welding. Residual stress measurement exhibited a M-shaped distribution. The samples joined at low travel speed and high tool rotational speed showed compressive residual stress in the joint region. Residual stress of the material lying below the tool shoulder is found to be tensile in nature. Also, it has been noticed that the residual stress in the AS is superior in magnitude than the RS of the weld specimen.
引用
收藏
页码：510 / 521
页数：12
相关论文
共 35 条
[21]   Effect of rotation speed and welding speed on Friction Stir Welding of AA1100 Aluminium alloy [J].
Raja, P. ;
Bojanampati, S. ;
Karthikeyan, R. ;
Ganithi, R. .
INTERNATIONAL CONFERENCE ON RECENT ADVANCES IN MATERIALS & MANUFACTURING TECHNOLOGIES, 2018, 346
[22]   Grain Size Optimization Using PSO Technique for Maximum Tensile Strength of Friction Stir-Welded Joints of AA1100 Aluminium [J].
Senapati, N. Pallavi ;
Bhoi, R. K. .
ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING, 2020, 45 (07) :5647-5656
[23]   An experimental investigation of temperature distribution and joint properties of Al 7075 T651 friction stir welded aluminium alloys [J].
Shah, P. H. ;
Badheka, Vishvesh .
3RD INTERNATIONAL CONFERENCE ON INNOVATIONS IN AUTOMATION AND MECHATRONICS ENGINEERING 2016, ICIAME 2016, 2016, 23 :543-550
[24]   The effect of hardening laws and thermal softening on modeling residual stresses in FSW of aluminum. alloy 2024-T3 [J].
Sonne, M. R. ;
Tutum, C. C. ;
Hattel, J. H. ;
Simar, A. ;
de Meester, B. .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2013, 213 (03) :477-486
[25]   Dissimilar friction stir welds in AA5083-AA6082: The effect of process parameters on residual stress [J].
Steuwer, A. ;
Peel, M. J. ;
Withers, P. J. .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2006, 441 (1-2) :187-196
[26]   Comparison of residual stress distributions in conventional and stationary shoulder high-strength aluminum alloy friction stir welds [J].
Sun, Tianzhu ;
Roy, M. J. ;
Strong, David ;
Withers, Philip J. ;
Prangnell, Philip B. .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2017, 242 :92-100
[27]   Microstructural studies of friction stir welds in 2024-T3 aluminum [J].
Sutton, MA ;
Yang, B ;
Reynolds, AP ;
Taylor, R .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2002, 323 (1-2) :160-166
[28]  
Verma S, 2017, MATER TODAY-PROC, V4, P1350, DOI 10.1016/j.matpr.2017.01.156
[29]   Effect of tool rotational speed on the microstructure and mechanical properties of bobbin tool friction stir welding of Al-Li alloy [J].
Wang, F. F. ;
Li, W. Y. ;
Shen, J. ;
Hu, S. Y. ;
dos Santos, J. F. .
MATERIALS & DESIGN, 2015, 86 :933-940
[30]   Overview -: Residual stress part 1 -: Measurement techniques [J].
Withers, PJ ;
Bhadeshia, HKDH .
MATERIALS SCIENCE AND TECHNOLOGY, 2001, 17 (04) :355-365
1234