Machining performance of a grooved tool in dry machining Ti-6Al-4 V

被引:17
作者
Sun, Fujian [1 ]
Qu, Shengguan [1 ]
Pan, Yuxiang [1 ]
Li, Xiaoqiang [1 ]
Yang, Chao [1 ]
机构
[1] S China Univ Technol, Sch Mech & Automot Engn, Guangzhou 510640, Guangdong, Peoples R China
关键词
Dry machining; Ti-6Al-4; V; A grooved tool; Machining performance; WEAR CHARACTERISTICS; SURFACE-ROUGHNESS; CBN TOOLS; TITANIUM; ALLOY; PREDICTION; LIFE;
D O I
10.1007/s00170-014-5861-0
中图分类号
TP [自动化技术、计算机技术];
学科分类号
0812 ;
摘要
In this paper, dry machining experiment of Ti-6Al-4 V was carried out to investigate the machining performance of a grooved tool in terms of its wear mechanisms and the effects of cutting parameters (cutting speed, feed rate, and cutting depth) on tool life and surface roughness of the machined workpiece. The results showed that chip-groove configuration substantially improved the machining performance of cutting tool. The main wear mechanisms of the grooved tool were adhesive wear, stripping wear, crater wear, and dissolution-diffusion wear. The resistance to chipping was enhanced due to the decrease of contact pressure of tool-chip interface. And the resistance to plastic deformation of tool nose was weakened at the cutting speed of more than 60 m/min. The appropriate cutting speed and feed rate were less than 70 m/min and 0.10 mm/r, respectively. With cutting speed increasing, the surface roughness of machined workpiece decreased. A high feed rate helped the formation of higher surface roughness except 0.21 mm/r. When cutting depth increased, tool nose curvature and phase transformation of workpiece material had great impact on surface roughness.
引用
收藏
页码:613 / 622
页数:10
相关论文
共 50 条
  • [31] Optimization of Machining parameters in EDM of Ti-6Al-4 V alloy using Taguchi Grey relational analysis Methodology
    Singh, Sandeep Kumar
    Prabhakar, Sunil
    Rao, Dinesh Kumar
    Khare, Sanchit Kumar
    MATERIALS TODAY-PROCEEDINGS, 2022, 59 : 1231 - 1235
  • [32] Influence of Al203 particle mixed dielectric fluid on machining performance of Ti6Al4V
    Ranjith, R.
    Prabhakar, Manoj B. S.
    Giridharan, P. K.
    Ramu, M.
    SURFACE TOPOGRAPHY-METROLOGY AND PROPERTIES, 2021, 9 (04)
  • [33] Precipitation effect on Surface roughness at Ti-6Al-4 V ELI alloy during Ultra-Precision Machining
    K Manjunath
    Suman Tewary
    Neha Khatri
    Kai Cheng
    International Journal on Interactive Design and Manufacturing (IJIDeM), 2023, 17 : 2607 - 2615
  • [34] A comparative study on the machinability of Ti-6Al-4V using conventional flood coolant and sustainable dry machining
    Dawood, Abdulhameed
    Arbuckle, Gregory K.
    Jahan, Muhammad P.
    International Journal of Machining and Machinability of Materials, 2015, 17 (06) : 507 - 528
  • [35] Evaluation of PVD-Inserts Performance and Surface Integrity When Turning Ti-6Al-4v ELI under Dry Machining
    Ibrahim, G. A.
    Haron, C. H. Che
    Ghani, J. A.
    ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES II, PTS 1 AND 2, 2011, 264-265 : 1050 - 1055
  • [36] EFFECT OF MICRO SCALE TEXTURES ON DRILLING PERFORMANCE OF CARBIDE TOOLS IN DRY AND WET MACHINING OF TI-6AL-4V
    Saseendran, Niketh
    Lodi, Samuel Gonumakulapalle
    PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, 2016, VOL. 2, 2016,
  • [37] Optimization of Wire Electric Discharge Machining Parameters in Machining of Ti-6Al-4V Alloy
    Sneha, P.
    Mahamani, A.
    Kakaravada, Ismail
    MATERIALS TODAY-PROCEEDINGS, 2018, 5 (02) : 6722 - 6727
  • [38] Online Tool Wear Monitoring by the Analysis of Cutting Forces in Transient State for Dry Machining of Ti6Al4V Alloy
    Sanchez Hernandez, Yezika
    Trujillo Vilches, F. Javier
    Bermudo Gamboa, Carolina
    Sevilla Hurtado, Lorenzo
    METALS, 2019, 9 (09)
  • [39] Sustainable dry machining of Ti-6 Al-4 V alloy via 3D resonant vibration assisted machining
    Saood Ali
    Rendi Kurniawan
    Moran Xu
    Tae Jo Ko
    The International Journal of Advanced Manufacturing Technology, 2025, 138 (11) : 5149 - 5163
  • [40] Predictive modeling of surface roughness in ultrasonic machining of cryogenic treated Ti-6Al-4V
    Dhuria, Gaurav
    Singh, Rupinder
    Batish, Ajay
    ENGINEERING COMPUTATIONS, 2016, 33 (08) : 2377 - 2394