Effect of VN alloy addition on the microstructure and wear resistance of Co-based alloy coatings

被引：22

作者：

Ding, Lin ^{[1
]}

Hu, Shengsun ^{[1
]}

Quan, Xiumin ^{[2
]}

Shen, Junqi ^{[1
]}

机构：

[1] Tianjin Univ, Sch Mat Sci & Engn, Tianjin Key Lab Adv Joining Technol, Tianjin 300072, Peoples R China

[2] Luan Vocat Technol Coll, Sch Automobile & Mech & Elect Engn, Luan 237158, Peoples R China

来源：

JOURNAL OF ALLOYS AND COMPOUNDS | 2016年 / 659卷

关键词：

Laser cladding; VN alloy; Co-based; Wear resistance; Stacking fault;

D O I：

10.1016/j.jallcom.2015.11.036

中图分类号：

O64 [物理化学（理论化学）、化学物理学];

学科分类号：

070304 ; 081704 ;

摘要：

VN alloy/Co-based composite coatings were prepared on the mild steel substrate by laser cladding. The effect of different amounts of VN alloy on the microstructure and wear resistance of Co-based coatings was investigated systematically by optical microscopy, X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, transmission electron microscopy, micro hardness testing and wear testing. The results showed phases of Co-based cladding coatings after adding VN alloy were gamma-Co, Cr23C6, Co5.47N, sigma-FeV and VN. A certain amount of fine grains and polygonal equiaxed grains synthesized as well as dense stacking fault and interaction of stacking fault were formed after adding VN alloy. The microhardness and wear resistance of coatings both improved greatly with a moderate additional amount of VN alloy. The improvement in microhardness and the reduction in wear loss were 12.0% and 36.4%, respectively, for 5.0 wt.% VN alloy, and the wear mechanism was abrasive wear. Thus, it is concluded that adding VN alloy is an effective and attainable way to improve the wear resistance of Co-based coatings. (C) 2015 Elsevier B.V. All rights reserved.

引用

页码：8 / 14

页数：7

共 23 条

[1]

Ocelik V., Furar I., De Hosson J.Th.M., Microstructure and properties of laser clad coatings studied by orientation imaging microscopy, Acta Mater., 58, pp. 6763-6772, (2010)

[2]

Verdi D., Garrido M.A., Munez C.J., Poza P., Mechanical properties of Inconel 625 laser cladded coatings: Depth sensing indentation analysis, Mater. Sci. Eng. A, 598, pp. 15-21, (2014)

[3]

Wang D., Hu Q., Zeng X., Microstructures and performances of Cr13Ni5Si2 based composite coatings deposited by laser cladding and laser-induction hybrid cladding, J. Alloys Compd., 588, pp. 502-508, (2014)

[4]

Amado J.M., Tobar M.J., Alvarez J.C., Lamas J., Yanez A., Laser cladding of tungsten carbides hardfacing alloys for the mining and mineral industry, Appl. Surf. Sci., 255, pp. 5553-5556, (2009)

[5]

Guo Y., Li Z., Yao C., Microstructure evolution of Fe-based nano-structured bainite coating by laser cladding, Mater. Des., 63, pp. 100-108, (2014)

[6]

Liu Y., Wang H.M., Microstructure and wear property of laser-clad Co3Mo2Si/Coss wear resistant coatings, Surf. Coatings Technol., 205, pp. 377-382, (2010)

[7]

Hemmati I., Ocelik V., De Hosson J.Th.M., Toughening mechanism for Ni-Cr-B-Si-C laser deposited coatings, Mater. Sci. Eng. A, 582, pp. 305-315, (2013)

[8]

Serres N., Portha N., Machi F., Influence of salt fog aging tests on mechanical resistance of laser clad-coatings, Surf. Coatings Technol., 205, pp. 5330-5337, (2011)

[9]

Huang Y., Zeng X., Investigation on cracking behavior of Ni-based coating by laser-induction hybrid cladding, Appl. Surf. Sci., 256, pp. 5985-5992, (2010)

[10]

Del Val J., Comesana R., Lusquinos F., Boutinguiza M., Riveiro A., Quintero F., Pou J., Laser cladding of Co-based super-alloy coatings: Comparative study between Nd:YAG laser and fibre laser, Surf. Coatings Technol., 204, pp. 1957-1961, (2010)

← 1 2 3 →