AN INVESTIGATION OF PCD 1600 GRADE INSERT ON MACHINING Al/SiC/B4C HYBRID COMPOSITES BASED ON THE TAGUCHI TECHNIQUES

被引：0
|
作者：
Maheshbabu, T. S. [1 ]
Krishnan, N. Muthu [2 ]
机构：
[1] Sathyabama Univ, Dept Aeronaut Engn, Madras 600119, Tamil Nadu, India
[2] Sri Venkateswara Coll Engn, Dept Mech Engn, Sriperumbudur 602105, Tamil Nadu, India
来源：
JOURNAL OF THE BALKAN TRIBOLOGICAL ASSOCIATION | 2014年 / 20卷 / 03期
关键词：
turning; hybrid MMCs; machinability; measurement; tool wear; grey relational analysis; METAL-MATRIX COMPOSITES; SURFACE-ROUGHNESS; TOOL WEAR; PARAMETERS; OPTIMIZATION; BEHAVIOR; METHODOLOGY; FATIGUE;
D O I：
暂无
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
Turning is a metal removal process and is important for the final assembly stage prior to application. This paper discusses the influence of machining parameters on turning characteristics of hybrid Metal Matrix Composites (MMCs) - (Al356/10SiCp/-5B(4)C). The composites are fabricated using stir casting method. The Taguchi design of experiments and grey relational analyses were employed to analyse the turning characteristics of the composite. The experiments were conducted to study the effect of cutting speed and feed rate on surface finish and power consumed using Poly Crystalline Diamond (PCD) 1600 grade insert. The results reveal that the dependent variables are greatly influenced by the feed rate rather than cutting speed for the composite. The confirmation experiment indicates that there is a good agreement between the estimated value and experimental value of the Grey relational grade.
引用
收藏
页码：463 / 478
页数：16
相关论文
共 50 条
  • [31] Tribological behaviour of aluminium based hybrid metal matrix composites (Al6061/B4C/ZrO2/SiC)
    Muzeer, S.
    MATERIALS TODAY-PROCEEDINGS, 2022, 56 : 507 - 513
  • [32] The deformation of B4C particle in the B4C/2024Al composites after high velocity impact
    Zhou, Zhisong
    Wu, Gaohui
    Jiang, Longtao
    Xu, Zhongguo
    MICRON, 2014, 67 : 107 - 111
  • [33] Mechanical Characteristics and Wear Behaviour of Al/SiC and Al/SiC/B4C Hybrid Metal Matrix Composites Fabricated Through Powder Metallurgy Route
    P. Bharathi
    T. Sampath kumar
    Silicon, 2023, 15 : 4259 - 4275
  • [34] Microstructure and Mechanical Properties of Fine Structured B4C/2024 Al Composites with High B4C Content
    Zheng, Ruixiao
    Ma, Fengmei
    Zhang, Yitan
    Ma, Chaoli
    ADVANCED ENGINEERING MATERIALS, 2017, 19 (07)
  • [35] Microstructure, mechanical, and oxidation properties of Mo-SiC/B4C hybrid composites
    Houssain, Hasaneen
    Islak, Serkan
    Okay, Faik
    Cabbar, Tuncer
    CERAMICS INTERNATIONAL, 2025, 51 (08) : 10375 - 10382
  • [36] Wear properties of Al6061/SiC + B4C + TiC hybrid composites produced by vacuum infiltration method
    Duru, Nurcihan
    Kaner, Sidem
    Kaplan, Yavuz
    Sever, Nimet Kardes
    Ozer, Alpay
    Aksoz, Sinan
    MATERIALS TESTING, 2024, 66 (12) : 2087 - 2097
  • [37] INVESTIGATION OF MATERIAL REMOVAL RATE AND SURFACE ROUGHNESS DURING ELECTRICAL DISCHARGE MACHINING ON Al (6061)-5%SiC-10%B4C HYBRID COMPOSITE
    Ibrahim, Abbas Fadhil
    Singal, Abdullah Hamad
    Noori, Diana Abed al Kareem
    METALLURGICAL & MATERIALS ENGINEERING, 2022, 28 (01) : 47 - 60
  • [38] Optimization of drilling parameters in hybrid (Al6061/SiC/B4C/talc) composites by grey relational analysis
    C. Ramesh Kumar
    V. JaiGanesh
    R. Ravi Raja Malarvannan
    Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2019, 41
  • [39] Some studies on mechanical and machining characteristics of Al2219/n-B4C/MoS2 nano-hybrid metal matrix composites
    Kumar, N. G. Siddesh
    Shankar, G. S. Shiva
    Basavarajappa, S.
    Suresh, R.
    MEASUREMENT, 2017, 107 : 1 - 11
  • [40] Application of Taguchi's method to study the effect of processing parameters of Al6082/B4C/Al2SiO5 hybrid composites on mechanical properties
    Puneeth, N.
    Satheesh, J.
    Koti, V.
    Koppad, Praveennath G.
    Akbarpour, M. R.
    Naveen, G. J.
    MATERIALS RESEARCH EXPRESS, 2019, 6 (10)
12345