Effect of Finishing and Polishing on the Surface Roughness and Gloss of Feldspathic Ceramic for Chairside CAD/CAM Systems

被引:48
作者
Carrabba, M. [1 ]
Vichi, A. [1 ]
Vultaggio, G. [1 ]
Pallari, S. [1 ]
Paravina, R. [2 ]
Ferrari, M. [1 ]
机构
[1] Univ Siena, Dept Mediacal Biotechnol, Policlin Scotte,Viale Bracci, I-53100 Siena, Italy
[2] Univ Texas Houston, Sch Dent, Dept Restorat Dent & Prosthodont, Houston, TX USA
关键词
RESTORATIVE MATERIALS; RESIN COMPOSITES; SCANNING-ELECTRON; IN-VITRO; ENAMEL; PERFORMANCE; MICROSCOPY; PORCELAIN; RETENTION; ADHESION;
D O I
10.2341/15-174-L
中图分类号
R78 [口腔科学];
学科分类号
1003 ;
摘要
Objectives: To evaluate surface roughness and gloss of feldspathic ceramic blocks for chair-side CAD/CAM systems before and after finishing and polishing. Methods: VITA Mark II ceramic blocks for the CEREC CAD/CAM system were cut perpendicularly in order to obtain a total of 70 specimens (14 3 18 3 3 mm). The flat surface was roughened using a grinder/polisher with dry 120-grit silicone-carbide paper. Surface roughness and gloss were measured using a digital profilometer (Ra) and a glossmeter (GU), respectively. Specimens were randomly divided into seven groups (n=10) based on the finishing/polishing system as follows: 1) Identoflex NGPorcelain Polisher (INP), 2) Identoflex Diamond Ceramic Polisher (IDP), 3) Hiluster Polishing System (HPS), 4) OptraFine (OF), 5) Identoflex Lucent (IL), 6) VITA Akzent Glaze Spray (AGS), and 7) VITA Shading Paste and Liquid (SPL). Surface analysis was repeated after the finishing/polishing treatment, and the obtained data were compared to the baseline in order to evaluate the Delta Ra and Delta GU. Results were statistically analyzed. The surface morphology was observed by scanning electron microscopy. Results: The mean surface roughness of polished systems increased in the order (statistical groups designated) SPLa < ILa < OFab < IDPbc < AGSbc < INPbc < HPSc and mean gloss decreased in the order AGSa > SPLa > OFab > ILabc > HPSbcd > INPcd > IDPd. Conclusions: The smoothest surface of CAD/CAM feldspathic ceramic blocks was achieved using the furnace-based glaze systems VITA Akzent Glaze Spray and VITA Shading Paste and Liquid and manual systems Identoflex Lucent and OptraFine.
引用
收藏
页码:175 / 184
页数:10
相关论文
共 44 条
[1]   The use of confocal microscopy to assess surface roughness of two milled CAD-CAM ceramics following two polishing techniques [J].
Al-Shammerya, Hazzah A. O. ;
Bubb, Nigel L. ;
Youngson, Callum C. ;
Fasbinder, Dennis J. ;
Wood, David J. .
DENTAL MATERIALS, 2007, 23 (06) :736-741
[2]  
[Anonymous], 1999, 2813 EN ISO
[3]   Comparison of different finishing/polishing systems on surface roughness and gloss of resin composites [J].
Antonson, Sibel A. ;
Yazici, A. Ruya ;
Kilinc, Evren ;
Antonson, Donald E. ;
Hardigan, Patrick C. .
JOURNAL OF DENTISTRY, 2011, 39 :E9-E17
[4]   Which mechanical and physical testing methods are relevant for predicting the clinical performance of ceramic-based dental prostheses? [J].
Anusavice, K. F. ;
Kakar, Kunian ;
Ferree, N. .
CLINICAL ORAL IMPLANTS RESEARCH, 2007, 18 :218-231
[5]   Fracture load of composite resin and feldspathic all-ceramic CAD/CAM crowns [J].
Attia, A ;
Abdelaziz, KM ;
Freitag, S ;
Kern, M .
JOURNAL OF PROSTHETIC DENTISTRY, 2006, 95 (02) :117-123
[6]   EFFECT OF DIFFERENT FINISHING TECHNIQUES FOR RESTORATIVE MATERIALS ON SURFACE ROUGHNESS AND BACTERIAL ADHESION [J].
Aykent, Filiz ;
Yondem, Isa ;
Ozyesil, Atilla G. ;
Gunal, Solen K. ;
Avunduk, Mustafa C. ;
Ozkan, Semiha .
JOURNAL OF PROSTHETIC DENTISTRY, 2010, 103 (04) :221-227
[7]  
Barucci-Pfister N, 2009, AM J DENT, V22, P102
[8]   Comparison of surface roughness of oral hard materials to the threshold surface roughness for bacterial plaque retention: A review of the literature [J].
Bollen, CML ;
Lambrechts, P ;
Quirynen, M .
DENTAL MATERIALS, 1997, 13 (04) :258-269
[9]  
Botta AC, 2009, AM J DENT, V22, P252
[10]  
Covey David A., 2011, General Dentistry, V59, P466