Influence of the Thickness Value on the Mechanical and Formability Properties of the CuZn37 Thin Sheet Metal

被引:1
作者
Brabie, Gheorghe [1 ]
Nanu, Neculai [1 ]
Jitaru, Augustin [1 ]
机构
[1] Univ Bacau, IMSI Dept, Bacau 600115, Romania
来源
INNOVATIVE MANUFACTURING ENGINEERING | 2013年 / 371卷
关键词
thin sheet metal; mechanical and formability properties; FLC; image correlation; GRAIN-SIZE; BEHAVIOR;
D O I
10.4028/www.scientific.net/AMM.371.163
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
The increase of the degree of miniaturization of the mechanical systems leads to the increase of the production requirements for micro or mili parts made using the micro and milli deep drawing processes. In the case of micro or mili drawn parts, the sheet thickness has an important influence on the intensity of the specific phenomena that occur during micro and milli cold forming and has also an important effect on the drawn part integrity or accuracy. The present study was focused on the investigation of the material behaviour, including mechanical properties and forming limit curve of CuZn37 when different thicknesses of sheets are used. For this purpose, experimental determinations were made by using the following two values of the sheet thickness: 0.1 and 0.2 mm. For each sheet thickness, the mechanical properties and the forming limit curves (FLC) were determined and compared. The obtained results concerning the influence of the sheet thickness on the material mechanical and formability properties shown that the level of the stress strain curve determined for the sheet thickness having 0.1 mm is greater than in the case of sheet thickness having 0.2 mm but the maximum strain and the anisotropy coefficients are lower. The level of the forming limit curves (FLC) in the case of sheet thickness having 0.2 mm is greater than in the case when the sheet thickness is equal to 0.1 mm.
引用
收藏
页码:163 / 167
页数:5
相关论文
共 10 条
  • [1] SIZE EFFECTS ON MATERIAL BEHAVIOR IN MICROFORMING
    Barbier, C.
    Thibaud, S.
    Richard, F.
    Picart, P.
    [J]. INTERNATIONAL JOURNAL OF MATERIAL FORMING, 2009, 2 : 625 - 628
  • [2] Modeling of grain size effect on micro deformation behavior in micro-forming of pure copper
    Chan, W. L.
    Fu, M. W.
    Lu, J.
    Liu, J. G.
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2010, 527 (24-25): : 6638 - 6648
  • [3] Microforming - from basic research to its realization
    Engel, U
    Eckstein, R
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2002, 125 : 35 - 44
  • [4] Effects of lubrication conditions on micro deep drawing
    Gong, Feng
    Guo, Bin
    Wang, Chun Ju
    Shan, De Bin
    [J]. MICROSYSTEM TECHNOLOGIES-MICRO-AND NANOSYSTEMS-INFORMATION STORAGE AND PROCESSING SYSTEMS, 2010, 16 (10): : 1741 - 1747
  • [5] Modelling of friction with respect to size effects
    Hu, Z.
    Vollertsen, F.
    [J]. INTERNATIONAL JOURNAL OF MATERIAL FORMING, 2008, 1 (Suppl 1) : 1231 - 1234
  • [6] Realisation and application of size dependent FEM-simulation for deep drawing of rectangular work pieces
    Hu, Zhenyu
    [J]. CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY, 2011, 4 (01) : 90 - 95
  • [7] Estimation of grain size and grain orientation influence in microforming processes by Taylor factor considerations
    Justinger, H.
    Hirt, G.
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2009, 209 (04) : 2111 - 2121
  • [8] Sene N.A., 2008, P 17 INT C DES TECHN, P241
  • [9] State of the art in micro forming and investigations into micro deep drawing
    Vollertsen, F
    Hu, Z
    Niehoff, HS
    Theiler, C
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2004, 151 (1-3) : 70 - 79
  • [10] Classification of size effects and similarity evaluating method in micro forming
    Zhang, K. F.
    Kun, L.
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2009, 209 (11) : 4949 - 4953