TBC bond coat-top coat interface roughness: Influence on fatigue life and modelling aspects

被引:82
作者
Eriksson, Robert [1 ]
Sjostrom, Soren [1 ]
Brodin, Hakan [1 ,2 ]
Johansson, Sten [1 ]
Ostergren, Lars [3 ]
Li, Xin-Hai [2 ]
机构
[1] Linkopings Univ, Dept Management & Engn, Div Engn Mat, SE-58183 Linkoping, Sweden
[2] Siemens Ind Turbomachinery AB, SE-61283 Finspang, Sweden
[3] GKN Aerosp Engine Syst, SE-46181 Trollhattan, Sweden
关键词
Thermal barrier coating; TBC; Thermal cycling fatigue; Interface; Roughness; Ra; THERMAL BARRIER COATINGS; RESIDUAL-STRESSES; CRACK BEHAVIOR; SURFACE-ROUGHNESS; OXIDATION; THICKNESS; DELAMINATION; SIMULATION; PREDICTION; INITIATION;
D O I
10.1016/j.surfcoat.2013.09.051
中图分类号
TB3 [工程材料学];
学科分类号
0805 ; 080502 ;
摘要
Thermal barrier coatings (TBCs), when used in gas turbines, may fail through thermal fatigue, causing the ceramic top coat to spall off the metallic bond coat. The life prediction of TBCs often involves finite element modelling of the stress field close to the bond coat/top coat interface and thus relies on accurate modelling of the interface. The present research studies the influence of bond coat/top coat interface roughness on the thermal fatigue life of plasma sprayed TBCs. By using different spraying parameters, specimens with varying interface roughnesses were obtained. During thermal cycling it was found that higher interface roughness promoted longer thermal fatigue life. The interfaces were characterised by roughness parameters, such as Ra, Rq and R Delta q, as well as by autocorrelation, material ratio curves and slope distribution. The variation of spray parameters was found to affect amplitude parameters, such as Ra, but not spacing parameters, such as RSm. Three different interface geometries were tried for finite element crack growth simulation: cosine, ellipse and triangular shapes. The cosine model was found to be an appropriate interface model and a procedure for obtaining the necessary parameters, amplitude and wavelength, was suggested. The positive effect of high roughness on life was suggested to be due to a shift from predominantly interface failure, for low roughness, to predominantly top coat failure, for high roughness. (C) 2013 Elsevier B.V. All rights reserved.
引用
收藏
页码:230 / 238
页数:9
相关论文
共 51 条
[1]   Stress distributions in plasma-sprayed thermal barrier coatings as a function of interface roughness and oxide scale thickness [J].
Ahrens, M ;
Vassen, R ;
Stöver, D .
SURFACE & COATINGS TECHNOLOGY, 2002, 161 (01) :26-35
[2]   Assessment of TBC systems failure mechanisms using a fracture mechanics approach [J].
Aktaa, J ;
Sfar, K ;
Munz, D .
ACTA MATERIALIA, 2005, 53 (16) :4399-4413
[3]  
[Anonymous], 1996, ISO 11562
[4]  
[Anonymous], 4288 ISO
[5]   A parametric study of the stress state of thermal barrier coatings Part II:: cooling stresses [J].
Bäker, M ;
Rösler, J ;
Heinze, G .
ACTA MATERIALIA, 2005, 53 (02) :469-476
[6]   Dependence of splat remelt and stress evolution on surface roughness length scales in plasma sprayed thermal barrier coatings [J].
Basu, S. N. ;
Yea, G. ;
Khare, R. ;
McCandless, B. ;
Gevelber, M. ;
Wroblewski, D. .
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS, 2009, 27 (02) :479-484
[7]   Modeling of Coating Process, Phase Changes, and Damage of Plasma Sprayed Thermal Barrier Coatings on Ni-Base Superalloys [J].
Beck, Tilmann ;
Bialas, Marcin ;
Bednarz, Piotr ;
Singheiser, Lorenz ;
Bobzin, Kirsten ;
Bagcivan, Nazlim ;
Parkot, Daniel ;
Kashko, Tatyana ;
Petkovic, Jvica ;
Hallstedt, Bengt ;
Nemna, Sergey ;
Schneider, Jochen M. .
ADVANCED ENGINEERING MATERIALS, 2010, 12 (03) :110-126
[8]  
Bednarz P., 2006, THESIS RWTH AACHEN U
[9]   Finite element analysis of stress distribution in thermal barrier coatings [J].
Bialas, Marcin .
SURFACE & COATINGS TECHNOLOGY, 2008, 202 (24) :6002-6010
[10]  
Brodin H, 2009, CERAM ENG SCI PROC, V30, P113