The Very High Cycle Fatigue Behaviour of Ti-6Al-4V Alloy

被引：52

作者：

Janecek, M. ^{[1
]}

Novy, F. ^{[2
]}

Harcuba, P. ^{[1
]}

Strasky, J. ^{[1
]}

Trsko, L. ^{[3
]}

Mhaede, M. ^{[4
]}

Wagner, L. ^{[4
]}

机构：

[1] Charles Univ Prague, Dept Phys Mat, CZ-12116 Prague, Czech Republic

[2] Univ Zilina, Dept Mat Engn, Zilina, Slovakia

[3] Univ Zilina, Res Ctr, Zilina, Slovakia

[4] Tech Univ Clausthal, Inst Mat Sci & Technol, D-38678 Clausthal Zellerfeld, Germany

来源：

ACTA PHYSICA POLONICA A | 2015年 / 128卷 / 04期

关键词：

TITANIUM-ALLOYS; STRENGTH;

D O I：

10.12693/APhysPolA.128.497

中图分类号：

O4 [物理学];

学科分类号：

0702 ;

摘要：

The high cycle and very high cycle fatigue properties of the titanium alloy Ti-6Al-4V with a duplex microstructure were investigated at room temperature. High cycle fatigue tests were performed in the range from 10(4) to 10(7) cycles by rotating bending at the frequency of 30 Hz. The very high cycle fatigue tests were carried out in the range from 10(7) to 10(10) cycles in tension-compression on an ultrasonic fatigue testing machine at the frequency of 20 kHz. The stress amplitude was found to decrease with increasing number of cycles in the whole range from 10(4) up to 10(9) cycles and only at the highest number of cycles (N-F = 10(9)) the alloy exhibits the fatigue limit of 460 MPa. The detail fractographic analysis was performed to characterize the fatigue failure mechanisms. Both subsurface and surface crack initiation were observed in very high cycle fatigue region. No inclusions, but only local chemical inhomogeneity in microstructure was observed at the locations of subsurface fatigue crack initiation in alpha-grains.

引用

页码：497 / 502

页数：6

共 32 条

[1]

Appel F, 2011, GAMMA TITANIUM ALUMINIDE ALLOYS: SCIENCE AND TECHNOLOGY, P357

[2]

Bache MR, 1999, INT J FATIGUE, V21, pS105

[3] The effect of grain orientation on fracture morphology during high-cycle fatigue of Ti-6Al-4V [J].

Bantounas, Ioannis ;

Dye, David ;

Lindley, Trevor C. .

ACTA MATERIALIA, 2009, 57 (12) :3584-3595

[4]

Bathias C., 2005, MECH ENG SE

[5]

Buch A :., 1988, Fatigue Strength Calculation

[6] Fatigue behaviour of duplex stainless steels in the very high cycle regime [J].

Chai, Guocai .

INTERNATIONAL JOURNAL OF FATIGUE, 2006, 28 (11) :1611-1617

[7] Gigacycle fatigue properties for high-strength low-alloy steel at 100 Hz, 600 Hz, and 20 kHz [J].

Furuya, Y ;

Matsuoka, S ;

Abe, T ;

Yamaguchi, K .

SCRIPTA MATERIALIA, 2002, 46 (02) :157-162

[8] Fatigue endurance of Ti-6Al-4V alloy with electro-eroded surface for improved bone in-growth [J].

Janecek, Milos ;

Novy, Frantisek ;

Strasky, Josef ;

Harcuba, Petr ;

Wagner, Lothar .

JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS, 2011, 4 (03) :417-422

[9] A new function for fatigue curves characterization and its multiple merits [J].

Kohout, J ;

Vechet, S .

INTERNATIONAL JOURNAL OF FATIGUE, 2001, 23 (02) :175-183

[10]

Leyens Christoph., 2006, Titanium and Titanium Alloys: Fundamentals and Applications, DOI [10.1002/tox.23349, DOI 10.1002/SMLL.202102046]

← 1 2 3 4 →