Influence of strain path on nucleation and growth of voids in dual phase steel sheets

被引:47
作者
Samei, Javad [1 ]
Green, Daniel E. [1 ]
Cheng, Jia [1 ]
Lima, Murilo Soares de Carvalho [1 ]
机构
[1] Univ Windsor, Dept Mech Automot & Mat Engn, 401 Sunset Ave, Windsor, ON N9B 3P4, Canada
基金
加拿大自然科学与工程研究理事会;
关键词
Dual phase steel; Microstructure; Strain path; Voids; Forming limit curve; DUCTILE FRACTURE; DAMAGE; TRIAXIALITY; PLASTICITY; PREDICTION; CRITERION; MODELS;
D O I
10.1016/j.matdes.2015.12.103
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
The objectives of this work are to describe the nucleation and growth of voids in DP600 dual phase steel sheets formed along different strain paths, and to investigate the correlation between the micro-mechanisms of damage and the forming limits. DP600 sheet specimens were stretch-formed in uniaxial, plane strain and biaxial tension using the Marciniak Kuczynski formability test. The evolution of damage in the microstructure was correlated to the formability in each strain path by quantitatively analyzing void density, void area fraction, void aspect ratio and mean void size. Results showed that DP600 steel sheets have less formability in plane strain compared to uniaxial and biaxial tension due to the more rapid elongation and growth of voids. Moreover, the sheets safely deformed to much greater effective strains in biaxial tension due to the smaller mean void size and slower void growth. As proposed by Gurson Gurson (1977), Tvergaard and Needleman Tvergaard and Needleman (1984), void volume fraction is an important damage parameter. However, this work shows that void aspect ratio and mean void size also significantly influence the evolution of damage and the formability of dual phase steels. (C) 2015 Elsevier Ltd. All rights reserved.
引用
收藏
页码:1028 / 1037
页数:10
相关论文
共 50 条
  • [31] Influence of Strain Ratio on Surface Roughening in Biaxial Stretching of IF Steel Sheets
    Kubo, Masahiro
    Hama, Takayuki
    Tsunemi, Yusuke
    Nakazawa, Yoshiaki
    Takuda, Hirohiko
    ISIJ INTERNATIONAL, 2018, 58 (04) : 704 - 713
  • [32] Influence of steel substrate grain size on phase layers growth kinetics and thickness of zinc hot dipped steel sheets
    Asgari, H.
    Ashrafizadeh, F.
    Toroghinejad, M. R.
    IRONMAKING & STEELMAKING, 2009, 36 (02) : 145 - 148
  • [33] Investigation on strain localization and hardening of dual-phase steel by hetero-deformation induced stress
    Zhang, Zhen
    Wang, Nan
    Li, Jing
    Chen, Yongnan
    Wu, Gang
    Chen, Xi
    Zhao, Qinyang
    Luo, Jinheng
    JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2023, 25 : 1832 - 1843
  • [34] Static and fatigue performance of weld bonded dual phase steel sheets
    Sam, S.
    Shome, M.
    SCIENCE AND TECHNOLOGY OF WELDING AND JOINING, 2010, 15 (03) : 242 - 247
  • [35] Plastic Deformation Mechanism of Dual-phase Steel at Different Strain Rates
    Qihang Pang
    Zhenduo Zhao
    Mei Xu
    Zhen Xu
    Tan Zhao
    Journal of Wuhan University of Technology-Mater. Sci. Ed., 2020, 35 : 1142 - 1148
  • [36] Plastic Deformation Mechanism of Dual-phase Steel at Different Strain Rates
    Pang, Qihang
    Zhao, Zhenduo
    Xu, Mei
    Xu, Zhen
    Zhao, Tan
    JOURNAL OF WUHAN UNIVERSITY OF TECHNOLOGY-MATERIALS SCIENCE EDITION, 2020, 35 (06): : 1142 - 1148
  • [37] Correlative characterization and plasticity modeling of microscopic strain localizations in a dual phase steel
    Basu, Soudip
    Jaya, Balila Nagamani
    Seekala, Harita
    Phani, P. Sudharshan
    Patra, Anirban
    Ganguly, Sarbari
    Dutta, Monojit
    Samajdar, Indradev
    MATERIALS CHARACTERIZATION, 2023, 197
  • [38] Effects of ferrite grain characteristics on strain distribution of dual-phase steel
    Ren, Chuang
    Dan, WenJiao
    Zhang, WeiGang
    MATERIALS RESEARCH EXPRESS, 2019, 6 (01)
  • [39] Damage mechanism and modeling of void nucleation process in a ferrite-martensite dual phase steel
    Saeidi, N.
    Ashrafizadeh, F.
    Niroumand, B.
    Forouzan, M. R.
    Barlat, F.
    ENGINEERING FRACTURE MECHANICS, 2014, 127 : 97 - 103
  • [40] Effect of strain-path change on the formability of DP-780 steel and Zn20 zinc sheets
    Daniel Schwindt, Claudio
    Schlosser, Fernando
    Walter Signorelli, Javier
    MATERIA-RIO DE JANEIRO, 2018, 23 (02):