Study of anneal hardening in cold worked Cu-Au alloy

被引:12
作者
Markovic, Ivana [1 ]
Nestorovic, Svetlana [1 ]
Markoli, Bostjan [2 ]
Premovic, Milena [3 ]
Mladenovic, Srba [1 ]
机构
[1] Univ Belgrade, Tech Fac Bor, Bor 19210, Serbia
[2] Univ Ljubljana, Fac Nat Sci & Engn, Ljubljana 1000, Slovenia
[3] Univ Pristina, Fac Tech Sci, Kosovska Mitrovica 38220, Serbia
关键词
Cu-Au alloy; Anneal hardening; Solute segregation; Short-range ordering; SHORT-RANGE-ORDER; ELECTRICAL-CONDUCTIVITY; MECHANICAL-PROPERTIES; PARTIAL DISLOCATIONS; SOLUTE SEGREGATION; THERMOMECHANICAL TREATMENT; PLASTIC-DEFORMATION; BINARY-ALLOYS; MICROSTRUCTURE; COPPER;
D O I
10.1016/j.jallcom.2015.10.208
中图分类号
O64 [物理化学(理论化学)、化学物理学];
学科分类号
070304 ; 081704 ;
摘要
An experimental study was carried out on cold worked Cu-12.7 wt.% Au alloy and pure copper, in order to compare the properties change during thermo-mechanical treatment. Hardness, microhardness, and electrical conductivity were studied as a function of annealing temperature and annealing time with the purpose of investigating the intensity of anneal hardening effect in cold worked Cu-12.7 wt.% Au alloy. Isochronal (up to 350 degrees C) and isothermal (at 250 degrees C for 100 h) annealing of cold worked alloy caused a two-stage increase in all of the measured properties. The mechanism responsible for this increase was analyzed using DTA, XRD, and TEM studies. The four stages observed in DTA heating curve were discussed in connection with the occurring processes. The reduction in the lattice parameter of cold worked Cu-12.7 wt.% Au alloy during annealing at 260 degrees C caused by the solute clustering, was observed. TEM studies did not show any presence of precipitates, other than disk-shaped areas with a higher degree of ordering. The achievement of high mechanical properties and high electrical conductivity in cold worked Cu-12.7 wt.% Au alloy after low temperature annealing was ascribed to the comparative effects of short-range ordering and solute segregation to lattice defects. (C) 2015 Elsevier B.V. All rights reserved.
引用
收藏
页码:414 / 421
页数:8
相关论文
共 50 条
  • [21] Characterization of prior cold worked and age hardened Cu-3Ti-1Cd alloy
    Markandeya, R
    Nagarjuna, S
    Sarma, DS
    MATERIALS CHARACTERIZATION, 2005, 54 (4-5) : 360 - 369
  • [22] Effect of Alloying Elements on Anneal-Hardening Behavior of Aluminum Alloy Foils
    Suzuki, Takashi
    Kuramoto, Shigeru
    Endo, Masaya
    Cui, Qi
    LIGHT METALS 2017, 2017, : 427 - 432
  • [23] Influence of degree of deformation in rolling on anneal hardening effect of a cast copper alloy
    Nestorovic, S
    Markovic, D
    Ivanic, L
    BULLETIN OF MATERIALS SCIENCE, 2003, 26 (06) : 601 - 604
  • [24] Diffusion Mobilities in fcc Cu-Au and fcc Cu-Pt Alloys
    Liu, Yajun
    Zhang, Lijun
    Yu, Di
    JOURNAL OF PHASE EQUILIBRIA AND DIFFUSION, 2009, 30 (02) : 136 - 145
  • [25] The identification of indigenous Cu and As metallophytes in the Lepanto Cu-Au Mine, Luzon, Philippines
    Claveria, Rene Juna R.
    Perez, Teresita R.
    Perez, Rubee Ellaine C.
    Algo, John Leo C.
    Robles, Patricia Q.
    ENVIRONMENTAL MONITORING AND ASSESSMENT, 2019, 191 (03)
  • [26] Density functional theory description of random Cu-Au alloys
    Tian, L-Y
    Levamaki, H.
    Kuisma, M.
    Kokko, K.
    Nagy, A.
    Vitos, L.
    PHYSICAL REVIEW B, 2019, 99 (06)
  • [27] Embedded atom method potential for studying mechanical properties of binary Cu-Au alloys
    Gola, Adrien
    Pastewka, Lars
    MODELLING AND SIMULATION IN MATERIALS SCIENCE AND ENGINEERING, 2018, 26 (05)
  • [28] Mineralization and Recent Exploration in the Chelopech Cu-Au deposit, Bulgaria
    Briggs, Terry
    Doychev, Plamen
    Teriyski, Strahil
    Angelov, Jordan
    Kuzmanova, Petya
    DIGGING DEEPER, VOLS 1 AND 2: DIGGING DEEPER, 2007, : 177 - 180
  • [29] Influence of pre-deformation on the precipitation hardening in Cu-Ni-Si alloy
    Donoso, Eduardo
    Jesus Dianez, Ma
    Criado, Jose M.
    REVISTA DE METALURGIA, 2019, 55 (04)
  • [30] Age-hardening characteristics of Cu-Ni-Si alloy after cold deformation
    Xiao, Xiangpeng
    Xiong, Baiqing
    Wang, Qiangsong
    Xie, Guoliang
    Peng, Lijun
    ADVANCED MATERIALS AND PROCESS TECHNOLOGY, PTS 1-3, 2012, 217-219 : 294 - 298