3D-Printing of a Lemon Battery via Fused Deposition Modelling and Electrodeposition

被引：0

作者：

Dijkshoorn, Alexander ^{[1
]}

Sculac, Luka ^{[1
]}

Sanders, Remco ^{[1
]}

Olthuis, Wouter ^{[2
]}

Stramigioli, Stefano ^{[1
]}

Krijnen, Gijs ^{[1
]}

机构：

[1] Univ Twente, Robot & Mechatron Grp, Enschede, Netherlands

[2] Univ Twente, BIOS Lab Chip Grp, Enschede, Netherlands

来源：

2020 IEEE INTERNATIONAL CONFERENCE ON FLEXIBLE AND PRINTABLE SENSORS AND SYSTEMS (IEEE FLEPS 2020) | 2020年

基金：

欧洲研究理事会;

关键词：

3D-Printing; Fused Deposition Modelling; Electrodeposition; Battery; Energy Storage;

D O I：

暂无

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

This paper introduces the fabrication of a lemon battery enabled through Fused Deposition Modelling (FDM) with commercially available filaments in combination with electrodeposition. The battery consists of a printed polylactic acid (PLA) structure with two 3D-printed, conductive polymer composite electrodes with a layer of deposited copper and zinc, immersed into a citric acid electrolyte. The current battery shows a capacity of at least 0.23 mWh, where the high internal resistance of around 310 ohms still poses a performance issue. The combined FDM and electrodeposition fabrication method presents a first step towards fabrication of arbitrarily shaped batteries without the need for parts assembly or chemical treatment of filaments, potentially powering co-printed electronics.

引用

页数：4

共 50 条

[1] Direct 3D-printing of phosphate glass by fused deposition modeling
Zaki, Reda Mohammed
Strutynski, Clement
Kaser, Simon
Bernard, Dominique
Hauss, Gregory
Faessel, Matthieu
Sabatier, Jocelyn
Canioni, Lionel
Messaddeq, Younes
Danto, Sylvain
Cardinal, Thierry
MATERIALS & DESIGN, 2020, 194
[2] Development and Characterization of PBSA-Based Green Composites in 3D-Printing by Fused Deposition Modelling
Niang, Babacar
Schiavone, Nicola
Askanian, Haroutioun
Verney, Vincent
Ndiaye, Diene
Diop, Abdoulaye Bouya
MATERIALS, 2022, 15 (21)
[3] Polymer Materials for 3D Printing (Fused Deposition Modelling)
Brovina S.D.
Guivan M.Y.
Mastalygina E.E.
Olkhov A.A.
Polymer Science - Series D, 2024, 17 (02) : 450 - 454
[4] The Precision and Accuracy of 3D Printing of Tablets by Fused Deposition Modelling
Macedo, Joana
da Costa, Nuno F.
Vanhoorne, Valerie
Vervaet, Chris
Pinto, Joao F.
JOURNAL OF PHARMACEUTICAL SCIENCES, 2022, 111 (10) : 2814 - 2826
[5] FUSED DEPOSITION MODELLING FOR 3D PRINTING OF SOFT ANTHROPOMORPHIC ACTUATORS
Curkovic, P.
Cubric, G.
INTERNATIONAL JOURNAL OF SIMULATION MODELLING, 2021, 20 (02) : 303 - 314
[6] Fused-Deposition-Material 3D-Printing Procedure and Algorithm Avoiding Use of Any Supports
Barile, Gianluca
Leoni, Alfiero
Muttillo, Mirco
Paolucci, Romina
Fazzini, Gianfranco
Pantoli, Leonardo
SENSORS, 2020, 20 (02)
[7] Composites based on metallic particles and tuned filling factor for 3D-printing by Fused Deposition Modeling
Palmero, Ester M.
Casaleiz, Daniel
de Vicente, Javier
Hernandez-Vicen, Juan
Lopez-Vidal, Silvia
Ramiro, Emilio
Bollero, Alberto
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING, 2019, 124
[8] Polypropylene Copolymers Designed for Fused Filament Fabrication 3D-Printing
Spiegel, Gunnar
Paulik, Christian
MACROMOLECULAR REACTION ENGINEERING, 2020, 14 (01)
[9] Bio-polyethylene reinforced with thermomechanical pulp fibers: Mechanical and micromechanical characterization and its application in 3D-printing by fused deposition modelling
Tarres, Q.
Melbo, J. K.
Delgado-Aguilar, M.
Espinach, F. X.
Mutje, P.
Chinga-Carrasco, G.
COMPOSITES PART B-ENGINEERING, 2018, 153 : 70 - 77
[10] Functionalized Design and Fused Deposition 3D-printing of Hierarchical Heterogeneous Isomeric Wave-absorbing Metamaterial
Yang Z.
Liang Q.
Duan Y.
Liu P.
Wang X.
Li D.
Liang, Qingxuan (liangqx728@xjtu.edu.cn), 1600, Chinese Mechanical Engineering Society (60): : 319 - 327

← 1 2 3 4 5 →