High-cycle fatigue properties of beta Ti alloy 55Ti-30Nb-10Ta-5Zr, gum metal

被引：4
作者：
Akita, M. [1 ]
Nakajima, M. [2 ]
Uematsu, Y. [3 ]
Tokaji, K. [3 ]
Kojima, T. [4 ]
机构：
[1] Gifu Univ, Fac Engn, Gifu 5011193, Japan
[2] Toyota Natl Coll Technol, Dept Mech Engn, Toyota 4718525, Japan
[3] Gifu Univ, Dept Mech Engn, Gifu 5011193, Japan
[4] Okuma Corp LTD, Oguchi, Aichi 4800193, Japan
来源：
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES | 2014年 / 37卷 / 11期
关键词：
beta titanium alloy; corrosion fatigue; crack growth; crack initiation; fatigue; slip deformation; S-N diagram; PLASTIC-DEFORMATION; TITANIUM; MECHANISM; BEHAVIOR; EVOLUTION;
D O I：
10.1111/ffe.12201
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
This paper describes the fatigue properties of the beta titanium alloy 55Ti-30Nb-10Ta-5Zr, generally referred to as 'Gum Metal'. Rotating bending fatigue tests have been performed in laboratory air and in a 3% NaCl aqueous solution. The results obtained were compared with those of a conventional beta titanium alloy, Ti-22V-4Al. In tensile tests, 55Ti-30Nb-10Ta-5Zr indicated elasticity and microplasticity in the elastic region. Thus, the elastic modulus slightly decreased with an increasing strain, and the work hardening was minimal during plastic deformation. The mechanical properties of both of the alloys were comparable. The fatigue strength of 55Ti-30Nb-10Ta-5Zr in laboratory air was higher than that of Ti-22V-4Al, which could be attributed to the higher fatigue crack initiation resistance of 55Ti-30Nb-10Ta-5Zr than Ti-22V-4Al, while the resistance to small fatigue crack growth was similar. The fatigue strength of 55Ti-30Nb-10Ta-5Zr in laboratory air and in the 3% NaCl aqueous solution was analogous. In addition, corrosion pits were not observed in the run-out specimen in the 3% NaCl aqueous solution, indicating a high resistance of 55Ti-30Nb-10Ta-5Zr against corrosion fatigue.
引用
收藏
页码：1223 / 1231
页数：9
相关论文
共 50 条
  • [41] Failure Behaviour and Energy Adsorption in Gum Metal (Ti-36Nb-2Ta-3Zr-O)
    Jones, Nicholas G.
    Tailing, Russell J.
    Lindley, Trevor C.
    Dye, David
    TI-2011: PROCEEDINGS OF THE 12TH WORLD CONFERENCE ON TITANIUM, VOL II, 2012, : 1169 - 1173
  • [42] Corrosion and tribocorrosion study of 316L steel, Ti-6Al-4V and Ti-10Zr-10Nb-5Ta
    Carquigny, S.
    Takadoum, J.
    Ivanescu, S.
    TRIBOLOGY-MATERIALS SURFACES & INTERFACES, 2019, 13 (02) : 112 - 119
  • [43] Influence of plasma and cold spray deposited Ti Layers on high-cycle fatigue properties of Ti6Al4V substrates
    Cizek, Jan
    Kovarik, Ondrej
    Siegl, Jan
    Khor, Khiam Aik
    Dlouhy, Ivo
    SURFACE & COATINGS TECHNOLOGY, 2013, 217 : 23 - 33
  • [44] Deposition, Characterization, and Corrosion Resistance of Nanocrystalline Bioactive Hydroxyapatite Ceramic Coating on New Ti-20Nb-10Zr-5Ta Alloy
    Popa, Monica
    Vasilescu, Ecaterina
    Drob, Paula
    Popa, Mihai Vasile
    Moreno, Jose Maria Calderon
    Vasilescu, Cora
    Drob, Silviu Iulian
    JOURNAL OF THE AMERICAN CERAMIC SOCIETY, 2012, 95 (12) : 3807 - 3814
  • [45] High-Temperature Deformation Characteristics of a β-Type Ti-29Nb-13Ta-4.6Zr Alloy
    Ghanbari, E.
    Zarei-Hanzaki, A.
    Farghadany, E.
    Abedi, H. R.
    Khoddam, Sh.
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2016, 25 (04) : 1554 - 1561
  • [46] Design and Development of Ti-Zr-Nb-Ta-Ag High Entropy Alloy for Bioimplant Applications
    Hussein, Mohamed Abdrabou
    Azeem, Mohammed Abdul
    Kumar, Arumugam Madhan
    Ankah, Nestor
    ADVANCED ENGINEERING MATERIALS, 2025, 27 (06)
  • [47] Fatigue performance and cyto-toxicity of low rigidity titanium alloy, Ti-29Nb-13Ta-4.6Zr
    Niinomi, M
    BIOMATERIALS, 2003, 24 (16) : 2673 - 2683
  • [48] The effect of ballistic impacts on the high-cycle fatigue properties of Ti-48Al-2Nb-2Cr (atomic percent)
    S. L. Draper
    M. V. Nathal
    B. A. Lerch
    J. M. Pereira
    C. M. Austin
    O. Erdmann
    Metallurgical and Materials Transactions A, 2001, 32 : 2743 - 2758
  • [49] Effect of oxygen on the microstructure, tensile properties and deformation behaviours of a biocompatible Ti40Zr25Nb25Ta10 high entropy alloy
    Mustafi, L.
    Nguyen, V. T.
    Song, T.
    Deng, Q.
    Jiang, L.
    Chen, X. B.
    Fabijanic, D. M.
    Qian, M.
    JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2025, 214 : 62 - 73
  • [50] Investigations on achievable surface quality in milling of Ti-35Nb-7Zr-5Ta alloy
    Leo Kumar, S. P.
    Avinash, D.
    MATERIALS AND MANUFACTURING PROCESSES, 2021, 36 (15) : 1800 - 1806
12345