Modeling the Static and Dynamic Behaviors of a Large Heavy-Duty Lathe Machine under Rated Loads

被引:3
|
作者
Lin, Chien-Yu [1 ,2 ]
Luh, Yuan-Ping [2 ]
Lin, Wei-Zhu [3 ]
Lin, Bo-Chen [1 ]
Hung, Jui-Pin [4 ]
机构
[1] L&L Machinery Ind Co Ltd, Dept Res & Dev, Taichung 41154, Taiwan
[2] Natl Taipei Univ Technol, Grad Inst Mfg Technol, Taipei 10608, Taiwan
[3] Natl Chin Yi Univ Technol, Dept Mech Engn, Taichung 41170, Taiwan
[4] Natl Chin Yi Univ Technol, Grad Inst Precis Mfg, Taichung 41170, Taiwan
关键词
dynamic rigidity; frequency response function; large heavy-duty lathe; five-axis turning-milling machine; FINITE-ELEMENT-METHOD; MATERIAL REMOVAL RATE; DEFORMATION; STABILITY; SHAFT;
D O I
10.3390/computation10120207
中图分类号
O1 [数学];
学科分类号
0701 ; 070101 ;
摘要
The static and dynamic performances of a machine tool structure are considered to constitute the primary factors affecting the load-carrying capacity, geometric accuracy and surface precision of the workpiece. The machining performance of a large machine tool under stable conditions is effectively determined by its dynamic response to the cutting force at low-frequency excitation. This study, therefore, investigated the static and dynamic characteristics of a large heavy-duty lathe machine tool in which the headstock and tailstock comprised critical component modules supporting a large workpiece during low-speed machining. Using a finite element model, the influences of the structural modules on the static and dynamic characteristics of the lathe were analyzed, considering the effects of the workpiece load. The results indicated that the fundamental vibration modes of the lathe were primarily dominated by headstock, tailstock, and workpiece behaviors. The maximum compliances of the lathe under the rated load were found to occur at relatively low frequencies (22, 40.7, and 82.7 Hz) and increase with the reduction in workpiece weight. Notably, these modal frequencies were significantly higher than the maximum rotational speed of the spindle (450 rpm). In addition, the dynamic rigidity corresponding to the rated speed was higher than that induced at the natural frequency. These results indicate that the subject lathe possesses sufficient capacity to sustain the cutting load during stable turning machining. This study can, therefore, help designers improve the performance of machine tools for future fabrication.
引用
收藏
页数:18
相关论文
共 50 条
  • [11] Fault Diagnosis of Rotary Parts of a Heavy-Duty Horizontal Lathe Based on Wavelet Packet Transform and Support Vector Machine
    Jin, Hongyu
    Titus, Avitus
    Liu, Yulong
    Wang, Yang
    Han, Zhenyu
    SENSORS, 2019, 19 (19)
  • [12] Static and dynamic characteristic analysis and structure optimization for crossbeam structure of heavy-duty truss robot
    Wang J.
    Wang X.-K.
    Fu J.-H.
    Lu G.-D.
    Jin C.-C.
    Chen Y.-Z.
    Zhejiang Daxue Xuebao (Gongxue Ban)/Journal of Zhejiang University (Engineering Science), 2021, 55 (01): : 124 - 134
  • [13] MACHINE FOR CORROSION TESTING MATERIALS UNDER VARIOUS STATIC AND DYNAMIC LOADS
    PREIS, GA
    SUPRUNCH.VK
    PONOMARE.EP
    KANCHENK.LP
    SUPRUNCH.VV
    BERCHANS.OM
    TOVSTENK.YV
    INDUSTRIAL LABORATORY, 1970, 36 (11): : 1779 - &
  • [14] Reduced Dynamic Modeling for Heavy-Duty Hydraulic Manipulators With Multi-Closed-Loop Mechanisms
    Zhang, Yi
    Ding, Wenhua
    Deng, Hua
    IEEE ACCESS, 2020, 8 : 101708 - 101720
  • [15] Key point selection in large-scale FBG temperature sensors for thermal error modeling of heavy-duty CNC machine tools
    Jianmin Hu
    Zude Zhou
    Quan Liu
    Ping Lou
    Junwei Yan
    Ruiya Li
    Frontiers of Mechanical Engineering, 2019, 14 : 442 - 451
  • [16] Key point selection in large-scale FBG temperature sensors for thermal error modeling of heavy-duty CNC machine tools
    Hu, Jianmin
    Zhou, Zude
    Liu, Quan
    Lou, Ping
    Yan, Junwei
    Li, Ruiya
    FRONTIERS OF MECHANICAL ENGINEERING, 2019, 14 (04) : 442 - 451
  • [17] Finite element modeling and modal analysis of heavy-duty mechanical spindle under multiple constraints
    College of Mechanical Engineering and Applied Electronics Technology, Beijing University of Technology, Beijing 100124, China
    Jixie Gongcheng Xuebao, 3 (165-173):
  • [18] Finite difference method-based calculation of gravity deformation curve for the large-span beam of heavy-duty vertical lathe
    Han, Zhenyu
    Wang, Han
    Shao, Zhongxi
    Fu, Hongya
    Jiang, Hui
    Wang, Weishun
    ADVANCES IN MECHANICAL ENGINEERING, 2016, 8 (04) : 1 - 8
  • [19] Comparative Assessment of Machine Learning Techniques for Modeling Energy Consumption of Heavy-Duty Battery Electric Trucks
    Gonzalez, Emmanuel Hidalgo
    Garrido, Jacqueline
    Barth, Matthew
    Boriboonsomsin, Kanok
    2024 FORUM FOR INNOVATIVE SUSTAINABLE TRANSPORTATION SYSTEMS, FISTS, 2024,
  • [20] MODELING THE FUEL SPRAY OF A HIGH REACTIVITY GASOLINE UNDER HEAVY-DUTY DIESEL ENGINE CONDITIONS
    Pei, Yuanjiang
    Torelli, Roberto
    Tzanetakis, Tom
    Zhang, Yu
    Traver, Michael
    Cleary, David J.
    Som, Sibendu
    PROCEEDINGS OF THE ASME INTERNAL COMBUSTION ENGINE FALL TECHNICAL CONFERENCE, 2017, VOL 2, 2017,