Drilling Process on CFRP: Multi-Criteria Decision-Making with Entropy Weight Using Grey-TOPSIS Method

被引:17
|
作者
Tran, Quang-Phuoc [1 ]
Nguyen, Van-Nhat [2 ]
Huang, Shyh-Chour [1 ]
机构
[1] Natl Kaohsiung Univ Appl Sci, Dept Mech Engn, Kaohsiung 80778, Taiwan
[2] Hung Yen Univ Technol & Educ, Fac Mech Engn, Hung Yen 160000, Vietnam
来源
APPLIED SCIENCES-BASEL | 2020年 / 10卷 / 20期
关键词
CFRP; uncut fiber; delamination; entropy weight; TOPSIS; PROCESS PARAMETERS; MULTIOBJECTIVE OPTIMIZATION; MACHINING PARAMETERS; SELECTION; COMPOSITE; DELAMINATION; ALGORITHM; CRITERIA; COOLANT;
D O I
10.3390/app10207207
中图分类号
O6 [化学];
学科分类号
0703 ;
摘要
Moisture strongly affects the quality and mechanical specificity of carbon fiber reinforced plastic (CFRP) when using lubrication fluids during machining, and the significant impact of the cutting tool geometry and cryogenic gas cooling on CFRP machining capabilities are observed. The main body of this paper aims at making decisions about the optimum parameter of the drilling process while machining on CFRP base on the grey relational coefficient embed to the technique for order of preference by similarity to an ideal solution (Grey-TOPSIS). The entropy method was used to determine the weight of decision-making for handling a multiple measure decision-making response. The twist angle of the tool drill, lubrication, and feed rate were used as the input variables, and were analyzed while taking into account several multi-response outputs, such as the surface roughness, uncut fiber, and delamination. The result showed that a feed rate of 228 mm/min, the high-helix twist angle, and cryogenic CO2 lubrication leads the calculated value to close the relative value, which minimizes the value of the surface roughness, the uncut fiber, and the delamination. Finally, verification of the valid effect of each parameter process was conducted using analysis of variance. The results indicated that the lubrication was the highest remarkable criterion on the uncut fiber, the delamination, and the surface roughness. By integrating the advantage of grey systems theory, and the technique for order preference by similarity to an ideal solution, to evaluate and optimize the machining parameter, the results indicate that the proposed model is useful to facilitate the multi-criteria decision-making problem under the environment of uncertainty and vagueness. This relatively advanced approach is very effectual in rejecting process variation and a great assistive strategy than other multi-criteria decision-making approaches.
引用
收藏
页码:1 / 18
页数:18
相关论文
共 50 条
  • [41] Consensus among Multi-Criteria Decision-Making methods: Using methods as a voter
    Hocaoglu, M. Fatih
    Tosun, Emre
    JOURNAL OF THE FACULTY OF ENGINEERING AND ARCHITECTURE OF GAZI UNIVERSITY, 2024, 40 (01): : 103 - 120
  • [42] Comparison of design concepts in multi-criteria decision-making using level diagrams
    Reynoso-Meza, Gilberto
    Blasco, Xavier
    Sanchis, Javier
    Herrero, Juan M.
    INFORMATION SCIENCES, 2013, 221 : 124 - 141
  • [43] Multi-Criteria Decision Making using TOPSIS Method for Battery Type Selection in Hybrid Propulsion System
    Bayraktar, Murat
    Nuran, Mustafa
    TRANSACTIONS ON MARITIME SCIENCE-TOMS, 2022, 11 (01): : 45 - 53
  • [44] Environmental Risk Assessment of Dams in Construction Phase Using a Multi-Criteria Decision-Making (MCDM) Method
    Jozi, Seyed Ali
    Shoshtary, Mehrnoush Tabib
    Zadeh, Ali Reza Khayat
    HUMAN AND ECOLOGICAL RISK ASSESSMENT, 2015, 21 (01): : 1 - 16
  • [45] An interactive multi-criteria decision-making method for building performance design
    Han, Zhen
    Li, Xiaoqian
    Sun, Jiaqi
    Wang, Mo
    Liu, Gang
    ENERGY AND BUILDINGS, 2023, 282
  • [46] Finding a mix of renewable energy for different stakeholders by applying multi-criteria decision-making techniques
    Bilbao-Terol, Amelia
    Canal-Fernandez, Veronica
    Gonzalez-Perez, Carmen
    INTERNATIONAL TRANSACTIONS IN OPERATIONAL RESEARCH, 2025,
  • [47] The vital-immaterial-mediocre multi-criteria decision-making method
    Zakeri, Shervin
    Ecer, Fatih
    Konstantas, Dimitri
    Cheikhrouhou, Naoufel
    KYBERNETES, 2023, 52 (03) : 937 - 963
  • [48] Multi-attribute decision-making of cryogenically cooled micro-EDM drilling process parameters using TOPSIS method
    Manivannan, R.
    Kumar, M. Pradeep
    MATERIALS AND MANUFACTURING PROCESSES, 2017, 32 (02) : 209 - 215
  • [49] The Extended TOPSIS Method for Multi-criteria Decision Making Based on Hesitant Heterogeneous Information
    Zhang, Xiaolu
    Xu, Zeshui
    PROCEEDINGS OF THE 2ND INTERNATIONAL CONFERENCE ON SOFTWARE ENGINEERING, KNOWLEDGE ENGINEERING AND INFORMATION ENGINEERING (SEKEIE 2014), 2014, 114 : 81 - 86
  • [50] A Fermatean Fuzzy ELECTRE Method for Multi-Criteria Group Decision-Making
    Zhou, Li-Ping
    Wan, Shu-Ping
    Dong, Jiu-Ying
    INFORMATICA, 2022, 33 (01) : 181 - 224