Drilling Process on CFRP: Multi-Criteria Decision-Making with Entropy Weight Using Grey-TOPSIS Method

被引:17
|
作者
Tran, Quang-Phuoc [1 ]
Nguyen, Van-Nhat [2 ]
Huang, Shyh-Chour [1 ]
机构
[1] Natl Kaohsiung Univ Appl Sci, Dept Mech Engn, Kaohsiung 80778, Taiwan
[2] Hung Yen Univ Technol & Educ, Fac Mech Engn, Hung Yen 160000, Vietnam
来源
APPLIED SCIENCES-BASEL | 2020年 / 10卷 / 20期
关键词
CFRP; uncut fiber; delamination; entropy weight; TOPSIS; PROCESS PARAMETERS; MULTIOBJECTIVE OPTIMIZATION; MACHINING PARAMETERS; SELECTION; COMPOSITE; DELAMINATION; ALGORITHM; CRITERIA; COOLANT;
D O I
10.3390/app10207207
中图分类号
O6 [化学];
学科分类号
0703 ;
摘要
Moisture strongly affects the quality and mechanical specificity of carbon fiber reinforced plastic (CFRP) when using lubrication fluids during machining, and the significant impact of the cutting tool geometry and cryogenic gas cooling on CFRP machining capabilities are observed. The main body of this paper aims at making decisions about the optimum parameter of the drilling process while machining on CFRP base on the grey relational coefficient embed to the technique for order of preference by similarity to an ideal solution (Grey-TOPSIS). The entropy method was used to determine the weight of decision-making for handling a multiple measure decision-making response. The twist angle of the tool drill, lubrication, and feed rate were used as the input variables, and were analyzed while taking into account several multi-response outputs, such as the surface roughness, uncut fiber, and delamination. The result showed that a feed rate of 228 mm/min, the high-helix twist angle, and cryogenic CO2 lubrication leads the calculated value to close the relative value, which minimizes the value of the surface roughness, the uncut fiber, and the delamination. Finally, verification of the valid effect of each parameter process was conducted using analysis of variance. The results indicated that the lubrication was the highest remarkable criterion on the uncut fiber, the delamination, and the surface roughness. By integrating the advantage of grey systems theory, and the technique for order preference by similarity to an ideal solution, to evaluate and optimize the machining parameter, the results indicate that the proposed model is useful to facilitate the multi-criteria decision-making problem under the environment of uncertainty and vagueness. This relatively advanced approach is very effectual in rejecting process variation and a great assistive strategy than other multi-criteria decision-making approaches.
引用
收藏
页码:1 / 18
页数:18
相关论文
共 50 条
  • [21] Multi criteria decision making through TOPSIS and COPRAS on drilling parameters of magnesium AZ91
    Varatharajulu, M.
    Duraiselvam, Muthukannan
    Kumar, M. Bhuvanesh
    Jayaprakash, G.
    Baskar, N.
    JOURNAL OF MAGNESIUM AND ALLOYS, 2022, 10 (10) : 2857 - 2874
  • [22] Multi-criteria decision-making method based on a cross-entropy with interval neutrosophic sets
    Tian, Zhang-peng
    Zhang, Hong-yu
    Wang, Jing
    Wang, Jian-qiang
    Chen, Xiao-hong
    INTERNATIONAL JOURNAL OF SYSTEMS SCIENCE, 2016, 47 (15) : 3598 - 3608
  • [23] Determination of the Optimal Size of Photovoltaic Systems by Using Multi-Criteria Decision-Making Methods
    Guerrero-Liquet, Guido C.
    Oviedo-Casado, Santiago
    Sanchez-Lozano, J. M.
    Socorro Garcia-Cascales, M.
    Prior, Javier
    Urbina, Antonio
    SUSTAINABILITY, 2018, 10 (12)
  • [24] A Multi-Criteria Decision-Making Approach for Process Improvement of E-Jet: An Experimental Investigation
    Das, Raju
    Ball, Amit Kumar
    Roy, Shibendu Shekhar
    Murmu, Naresh Chandra
    JOURNAL OF ADVANCED MANUFACTURING SYSTEMS, 2020, 19 (03) : 463 - 497
  • [25] Application of multi-criteria decision-making (MCDM) methods on a meso-scale electrical discharge drilling (EDD) process
    Yildiz, Yakup
    SN APPLIED SCIENCES, 2020, 2 (11):
  • [26] APPLICATIONS OF WASPAS METHOD AS A MULTI-CRITERIA DECISION-MAKING TOOL
    Chakraborty, Shankar
    Zavadskas, Edmundas Kazimieras
    Antucheviciene, Jurgita
    ECONOMIC COMPUTATION AND ECONOMIC CYBERNETICS STUDIES AND RESEARCH, 2015, 49 (01): : 5 - 22
  • [27] Best-worst multi-criteria decision-making method
    Rezaei, Jafar
    OMEGA-INTERNATIONAL JOURNAL OF MANAGEMENT SCIENCE, 2015, 53 : 49 - 57
  • [28] Multi-Criteria Group Decision-Making Using an m-Polar Hesitant Fuzzy TOPSIS Approach
    Akram, Muhammad
    Adeel, Arooj
    Alcantud, Jose Carlos R.
    SYMMETRY-BASEL, 2019, 11 (06):
  • [29] A Method Based on SMAA-Topsis for Stochastic Multi-Criteria Decision Making and a Real-World Application
    Okul, Deniz
    Gencer, Cevriye
    Aydogan, Emel Kizilkaya
    INTERNATIONAL JOURNAL OF INFORMATION TECHNOLOGY & DECISION MAKING, 2014, 13 (05) : 957 - 978
  • [30] A Hybrid Multi-Criteria Decision-Making Approach Based on ANP-Entropy TOPSIS for Building Materials Supplier Selection
    Chen, Chun-Ho
    ENTROPY, 2021, 23 (12)