Open hole fatigue testing of laser machined MD-CFRPs

被引：29

作者：

Kalyanasundaram, Dinesh ^{[1
]}

Gururaja, Suhasini ^{[2
]}

Prabhune, Prajakta ^{[2
]}

Singh, Dilpreet ^{[1
]}

机构：

[1] IIT, Ctr Biomed Engn, Delhi, India

[2] Indian Inst Sci IISc, Aerosp Engn, Bangalore 12, Karnataka, India

来源：

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING | 2018年 / 111卷

关键词：

Polymer-matrix composites (PMCs); Fatigue; CT analysis; Ultrasonics; Machining; FIBER-REINFORCED COMPOSITES; DAMAGE; DELAMINATION; STRENGTH; SPECIMENS; PLASTICS; LIFE; FRPS;

D O I：

10.1016/j.compositesa.2018.05.005

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

The effect of fiber laser machining (FLM) on multi-directional carbon fiber reinforced plastics (MD-CFRP) with [0/90/45/ - 45]s lay-up was studied under tension-tension fatigue with stress ratio R = 0.1 for an open hole fatigue (OHF) test configuration. The FLM parameters were chosen to yield a heat affected zone (HAZ) corresponding to a damage factor of approximately 1.4. The growth of this initial damage under tension-tension fatigue was investigated using digital image correlation (DIC), and damage growth characterization was carried out using scanning acoustic microscopy (SAM) and micro computed tomography (micro-CT). The endurance limit of the MD-CFRPs was evaluated by examining the fatigue life at 70, 50 and 30% of its ultimate tensile strength. Results show a strong correlation of damage mode on the applied load levels like conventionally machined samples.

引用

页码：33 / 41

页数：9

共 50 条

[1] FATIGUE RESISTANCE OF IMPACT DAMAGED SPECIMENS VS MACHINED HOLE SPECIMENS
LAUDER, AJ
AMATEAU, MF
QUEENEY, RA
COMPOSITES, 1993, 24 (05): : 443 - 445
[2] Effect of laser shock peening and cold expansion on fatigue performance of open hole samples
Rubio-Gonzalez, Carlos
Gomez-Rosas, G.
Ruiz, R.
Nait, M.
Amrouche, A.
STRUCTURAL ENGINEERING AND MECHANICS, 2015, 53 (05) : 867 - 880
[3] Open-hole fatigue testing of UD-GFRP composite laminates containing aligned CNTs using infrared thermography
Pothnis, Jayaram R.
Hajagolkar, Akshay K.
Anilchandra, A. R.
Das, Raj
Gururaja, Suhasini
COMPOSITE STRUCTURES, 2023, 324
[4] Static and fatigue testing of open-hole and assembled composites based on long carbon fiber and a nylon matrix developed using fused deposition modelling: Multiscale characterization of printed holes and machined holes
Blais, Philippe
Toubal, Lotfi
Zitoune, Redouane
Chaib, Zouhair
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING, 2022, 162
[5] Fatigue in laser shock peened open-hole thin aluminium specimens
Ivetic, Goran
Meneghin, Ivan
Troiani, Enrico
Molinari, Gianluca
Ocana, Jose
Morales, Miguel
Porro, Juan
Lanciotti, Agostino
Ristori, Vjola
Polese, Claudia
Plaisier, Jasper
Lausi, Andrea
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2012, 534 : 573 - 579
[6] Residual stress and fatigue life in laser shock peened open hole samples
Cuellar, Servando D.
Hill, Michael R.
DeWald, Adrian T.
Rankin, Jon E.
INTERNATIONAL JOURNAL OF FATIGUE, 2012, 44 : 8 - 13
[7] Effect of drilling-induced damage on the open hole flexural fatigue of carbon/epoxy composites
Haeger, Andreas
Grudenik, Manuel
Hoffmann, Michael J.
Knoblauch, Volker
COMPOSITE STRUCTURES, 2019, 215 : 238 - 248
[8] The open hole tensile test: a challenge for virtual testing of composites
Hallett, Stephen R.
Green, Ben G.
Jiang, Wen-Guang
Cheung, Kin Hei
Wisnom, Michael R.
INTERNATIONAL JOURNAL OF FRACTURE, 2009, 158 (02) : 169 - 181
[9] Damage development in open-hole composite specimens in fatigue. Part 1: Experimental investigation
Nixon-Pearson, O. J.
Hallett, S. R.
Withers, P. J.
Rouse, J.
COMPOSITE STRUCTURES, 2013, 106 : 882 - 889
[10] Damage development in open-hole composite specimens in fatigue. Part 2: Numerical modelling
Nixon-Pearson, O. J.
Hallett, S. R.
Harper, P. W.
Kawashita, L. F.
COMPOSITE STRUCTURES, 2013, 106 : 890 - 898

← 1 2 3 4 5 →