APPLICATION OF ELECTRON BEAM MELTING (EBM) IN ADDITIVE MANUFACTURING OF AN IMPELLER

被引：18
|
作者：
Tan, Xepeng [1 ]
Kok, Yihong [1 ]
Tor, S. B. [1 ]
Chua, C. K. [1 ]
机构：
[1] Nanyang Technol Univ, NTU Addit Mfg Ctr, Sch Mech & Aerosp Engn, Singapore 637372, Singapore
来源：
PROCEEDINGS OF THE 1ST INTERNATIONAL CONFERENCE ON PROGRESS IN ADDITIVE MANUFACTURING | 2014年
关键词：
D O I：
10.3850/978-981-09-0446-3_076
中图分类号：
Q813 [细胞工程];
学科分类号：
摘要：
An industrial impeller has been successfully fabricated by using Ti-6Al-4V ELI powder via a newly installed Arcam A2XX electron beam melting (EBM) machine. EBM was found to be preferable to build the circular or complex-shaped parts with thin walls. Several problems that frequently take place during the EBM fabrication are proposed based on the practical experience. It is found that metallization peeling-off, warpage, "swelling" and arc trips are the main reasons resulting in the failures of building jobs. It is suggested to pay close attention to the following aspects: a thorough cleanliness of the entire EBM system before start, a reasonable placement of builds on the start plate, an optimized design on geometries, etc., for a successfully built part.
引用
收藏
页码：327 / 332
页数：6
相关论文
共 50 条
  • [21] Refining effect of electron beam melting on additive manufacturing of pure titanium products
    Park, Hyung Ki
    Ahn, Yong Keun
    Lee, Byoung Soo
    Jung, Kyung Hwan
    Lee, Chang Woo
    Kim, Hyung Giun
    MATERIALS LETTERS, 2017, 187 : 98 - 100
  • [22] Metal Fabrication by Additive Manufacturing Using Laser and Electron Beam Melting Technologies
    Murr, Lawrence E.
    Gaytan, Sara M.
    Ramirez, Diana A.
    Martinez, Edwin
    Hernandez, Jennifer
    Amato, Krista N.
    Shindo, Patrick W.
    Medina, Francisco R.
    Wicker, Ryan B.
    JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2012, 28 (01) : 1 - 14
  • [23] Numerical simulation for electron beam selective melting PBF additive manufacturing of molybdenum
    Muhammad Qasim Zafar
    Chaochao Wu
    Haiyan Zhao
    Du Kai
    Qianming Gong
    The International Journal of Advanced Manufacturing Technology, 2021, 117 : 1575 - 1588
  • [24] Additive Manufacturing of TiC/Steel Composites Using Electron Beam Melting and In Situ Infiltration
    Chen, Yong
    Fu, Zongwen
    Ye, Jihui
    Wahlmann, Benjamin
    Koerner, Carolin
    ADVANCED ENGINEERING MATERIALS, 2024, 26 (09)
  • [25] Additive Manufacturing of a Cold-Work Tool Steel using Electron Beam Melting
    Botero, Carlos
    Ramsperger, Markus
    Selte, Aydin
    Asvik, Kenneth
    Koptyug, Andrey
    Skoglund, Per
    Roos, Stefan
    Rannar, Lars-Erik
    Backstrom, Mikael
    STEEL RESEARCH INTERNATIONAL, 2020, 91 (05)
  • [26] Progress in electron beam additive manufacturing
    Markl, Matthias
    Colosimo, Bianca M.
    Koerner, Carolin
    PROGRESS IN ADDITIVE MANUFACTURING, 2024, 9 (05) : 1415 - 1415
  • [27] Chemical etching as a finishing process for Electron Beam Melting (EBM) Parts
    Dolimont, Adrien
    Demarbaix, Anthonin
    Ducobu, Francois
    Riviere-Lorphevre, Edouard
    PROCEEDINGS OF THE 22ND INTERNATIONAL ESAFORM CONFERENCE ON MATERIAL FORMING (ESAFORM 2019), 2019, 2113
  • [28] TEMPERATURE DISTRIBUTION AND FLUID FLOW MODELING OF ELECTRON BEAM MELTING® (EBM)
    Jamshidinia, M.
    Kong, F.
    Kovacevic, R.
    PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION - 2012, VOL 7, PTS A-D, 2013, : 3089 - +
  • [29] Fatigue properties of a dental implant produced by electron beam melting® (EBM)
    Jamshidinia, M.
    Wang, L.
    Tong, W.
    Ajlouni, Raed
    Kovacevic, R.
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2015, 226 : 255 - 263
  • [30] Surface Roughness Characterisation and Analysis of the Electron Beam Melting (EBM) Process
    Galati, Manuela
    Minetola, Paolo
    Rizza, Giovanni
    MATERIALS, 2019, 12 (13)
12345