Effect of precipitates on long-term creep deformation properties of P92 and P122 type advanced ferritic steels for USC power plants

被引：153

作者：

Yoshizawa, M. ^{[1
]}

Igarashi, M. ^{[1
]}

Moriguchi, K. ^{[1
]}

Iseda, A. ^{[2
]}

Armaki, Hassan Ghassemi ^{[3
]}

Maruyama, K. ^{[3
]}

机构：

[1] Sumitomo Met Ind Ltd, Corp Res & Dev Labs, Amagasaki, Hyogo 6600891, Japan

[2] Sumitomo Met Ind Ltd, Tubular Prod Technol Dept, Chuo Ku, Tokyo 1046111, Japan

[3] Tohoku Univ, Grad Sch Environm Studies, Sendai, Miyagi 9808579, Japan

来源：

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2009年 / 510-11卷

关键词：

Creep rupture strength; High Cr ferritic steel; Z-phase ultra supercritical (USC) boilers;

D O I：

10.1016/j.msea.2008.05.055

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

Long-term creep rupture strengths and the microstructural stability of ASME P92 and P122 pipes have been studied using creep testing at the temperatures from 550 to 700 degrees C and detailed scanning transmission electron microscopy. Creep rupture strength of P92 is found to be more stable than that of P122 at temperatures over 600 degrees C, which is mainly due to the difference in their Cr content. P122 type model steel with reduced Cr content, 9%Cr, has been prepared to explore the effect of Cr on the stability of MX and formation of Z-phase during creep deformation. MX in 9%Cr steel is found to be stable even after prolonged exposure at 650 degrees C, while Cr and Fe concentration to MX without marked coarsening has been observed in 10.5%Cr steel after aging for 10,000 h at 650 degrees C. This seems to lead to the transition of MX carbonitride into the Z-phase after aging for 23,000 h, which requires ordering in a M(2)N lattice to achieve a tetragonal Z-phase to be stable. Creep deformation behavior in the transient creep region of the steels is almost same up to about 7000 h, while in the acceleration creep region the creep rate of 10.5%Cr steel becomes much faster than that of 9%Cr steel, resulting in shorter rupture life. It is obvious that the creep rupture strength degradation starts prior to the formation of Z-phase in 10.5%Cr steel. It is thus concluded that Z-phase is not a necessary factor for degradation of creep rupture strength but the instability of the fine precipitates such as Cr(2)(C, N) caused by the compositions change like Cr supply to MX carbonitride is more essential. (C) 2008 Elsevier B.V. All rights reserved.

引用

页码：162 / 168

页数：7

共 20 条

[11]

MASUMOTO H, 1986, P 1 EPRI C IMPR COAL, P203

[12]

MASUYAMA F, 1998, P ADV HEAT RES STEEL, P33

[13]

MAYER KH, 2002, P 28 MPA SEM STUTTG

[14]

MORIGUCHI, PHYS REV B UNPUB

[15]

MURAMATSU K, 1998, P ADV HEAT RES STEEL, P543

[16]

SAWADA K, 2006, MAT ADV POWER ENG, P1227

[17]

Semba H., 2006, Energy Materials, V1, P238, DOI 10.1179/174892406X173611

[18]

Strang A, 1996, MATER SCI TECH SER, V12, P552, DOI 10.1179/026708396790165993

[19]

STRANG A, 2006, MAT ADV POWER ENG, P1251

[20] Two-phase separation of primary MX carbonitride during tempering in creep resistant 9Cr1MoVNb steel [J].

Suzuki, K ;

Kumai, S ;

Toda, Y ;

Kushima, H ;

Kimura, K .

ISIJ INTERNATIONAL, 2003, 43 (07) :1089-1094

← 1 2 →