Surface Roughness Investigation in the Hard Turning of Steel Using Ceramic Tools

被引：43

作者：

Ferreira, R. ^{[1
]}

Carou, D. ^{[1
]}

Lauro, C. H. ^{[1
]}

Davim, J. P. ^{[1
]}

机构：

[1] Univ Aveiro, Dept Mech Engn, P-3810193 Aveiro, Portugal

来源：

MATERIALS AND MANUFACTURING PROCESSES | 2016年 / 31卷 / 05期

关键词：

Ceramics; Dry; Geometry; Multi-radii; Roughness; Steel; Tool; Turning; CUTTING PARAMETERS; WIPER; FINISH; WEAR; OPTIMIZATION; D2;

D O I：

10.1080/10426914.2014.995051

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

The present work evaluates the use of conventional and multi-radii ceramic tools in the turning of AISI H13 in terms of surface quality. The selected design factors are the cutting speed, feed rate, and type of tool. To carry out this research, a design of experiments was used. The obtained results were analyzed using the analysis of variance (ANOVA), which allowed recognition of the influence of the feed rate and type of tool on the surface quality. By contrast, the cutting speed was found to be a factor that had no statistical significance. When comparing the experimental with the theoretical values, the results of the conventional and multi-radii tools were found to differ. In addition, it was highlighted that the feed rate has an important influence on the difference between the experimental and theoretical results.

引用

页码：648 / 652

页数：5

共 16 条

[1] State of the art in hard turning [J].

Bartarya, Gaurav ;

Choudhury, S. K. .

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2012, 53 (01) :1-14

[2] Effect of the lubrication-cooling technique, insert technology and machine bed material on the workpart surface finish and tool wear in finish turning of AISI 420B [J].

Bruni, C. ;

Forcellese, A. ;

Gabrielli, F. ;

Simoncini, M. .

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2006, 46 (12-13) :1547-1554

[3] Comparative wear behavior of ceramic and carbide tools during high speed machining of steel [J].

Chakraborty, A ;

Ray, KK ;

Bhaduri, SB .

MATERIALS AND MANUFACTURING PROCESSES, 2000, 15 (02) :269-300

[4] Machinability evaluation in hard turning of cold work tool steel (D2) with ceramic tools using statistical techniques [J].

Davim, J. Paulo ;

Figueira, Luis .

MATERIALS & DESIGN, 2007, 28 (04) :1186-1191

[5]

Davim JP, 2011, MACHINING OF HARD MATERIALS, P1, DOI 10.1007/978-1-84996-450-0

[6] Comparative assessment of wiper and conventional ceramic tools on surface roughness in hard turning AISI 4140 steel [J].

Elbah, Mohamed ;

Yallese, Mohamed Athmane ;

Aouici, Hamdi ;

Mabrouki, Tarek ;

Rigal, Jean-Francois .

MEASUREMENT, 2013, 46 (09) :3041-3056

[7] Surface roughness measurement in turning carbon steel AISI 1045 using wiper inserts [J].

Esteves Correia, A. ;

Paulo Davim, J. .

MEASUREMENT, 2011, 44 (05) :1000-1005

[8] Machinability investigations in hard turning of AISI D2 cold work tool steel with conventional and wiper ceramic inserts [J].

Gaitonde, V. N. ;

Karnik, S. R. ;

Figueira, Luis ;

Davim, J. Paulo .

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS, 2009, 27 (04) :754-763

[9] Surface finish generated in hard turning of quenched alloy steel parts using conventional and wiper ceramic inserts [J].

Grzesik, W. ;

Wanat, T. .

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2006, 46 (15) :1988-1995

[10]

Klocke F., 2005, CIRP ANN-MANUF TECHN, V54, P22, DOI DOI 10.1016/S0007-8506(07)60018-3

← 1 2 →