Load-carrying capacity of filament-wound E glass/epoxy composite rings

被引：2

作者：

Beylergil, Bertan ^{[1
]}

机构：

[1] Alanya Alaaddin Keykubat Univ, Fac Engn, Mech Engn Dept, TR-07450 Alanya Antalya, Turkey

来源：

TRANSACTIONS OF THE CANADIAN SOCIETY FOR MECHANICAL ENGINEERING | 2019年 / 43卷 / 02期

关键词：

composite; filament winding; ring; strength; hoop testing; DAMAGE; THICK; TUBES; FAILURE;

D O I：

10.1139/tcsme-2018-0107

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

In this study, three different types of E glass/epoxy composite rings were produced by the filament-winding technique: (i) O ring (Type A), (ii) ring with a radial notch (Type B), and (iii) C-shaped ring (Type C). To evaluate the effect of winding angle on the load-carrying capacity of composite rings, five different winding angles were considered: +/- 45 degrees, +/- 55 degrees, +/- 65 degrees, +/- 75 degrees, and +/- 88 degrees. The load capacity of the manufactured composite rings in the tensile hoop direction were determined experimentally using a special test fixture. The experimental results showed that the optimum winding angle was +/- 88 degrees in terms of load-carrying capacity. The rings wound at 55 degrees had the lowest load-carrying capacity. Type A rings had the highest capacity while Type C rings had the lowest.

引用

页码：173 / 178

页数：6

共 21 条

[1] Buckling and post-buckling of filament wound composite tubes under axial compression: Linear, nonlinear, damage and experimental analyses [J].

Almeida, Jose Humberto S., Jr. ;

Tonatto, Maikson L. P. ;

Ribeiro, Marcelo L. ;

Tita, Volnei ;

Amico, Sandro C. .

COMPOSITES PART B-ENGINEERING, 2018, 149 :227-239

[2] Damage modeling for carbon fiber/epoxy filament wound composite tubes under radial compression [J].

Almeida, Jose Humberto S., Jr. ;

Ribeiro, Marcelo L. ;

Tita, Volnei ;

Amico, Sandro C. .

COMPOSITE STRUCTURES, 2017, 160 :204-210

[3] Damage and failure in carbon/epoxy filament wound composite tubes under external pressure: Experimental and numerical approaches [J].

Almeida, Jose Humberto S., Jr. ;

Ribeiro, Marcelo L. ;

Tita, Volnei ;

Amico, Sandro C. .

MATERIALS & DESIGN, 2016, 96 :431-438

[4] Load sharing ability of the liner in type III composite pressure vessels under internal pressure [J].

Almeida, Jose Humberto S., Jr. ;

Faria, Hugo ;

Marques, Antonio T. ;

Amico, Sandro C. .

JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2014, 33 (24) :2274-2286

[5]

[Anonymous], 2019, ASTM D5379/D5379M-12, DOI [10.1520/D5379_D5379M-12, DOI 10.1520/D5379_D5379M-12]

[6]

[Anonymous], 2014, Standard test methods for maximum index density and unit weight of soils using a vibratory table, DOI [DOI 10.1520/D3039, DOI 10.1520/D3039_D3039M-17]

[7]

[Anonymous], J COMPOS MAT

[8]

[Anonymous], THESIS

[9]

[Anonymous], 2016, Annual Book of ASTM, P1, DOI [10.1520/D3410_D3410M-16, DOI 10.1520/D3410_D3410M-16]

[10] Experimental evaluation of the effect of the structure of composite rings on their properties in the radial direction [J].

Arnautov, AK ;

Zhmud, NP .

MECHANICS OF COMPOSITE MATERIALS, 2002, 38 (06) :505-514

← 1 2 3 →