Enhanced Multipactor Performance in 3D Printed Microwave Parts

被引：0
|
作者：
Martin-Iglesias, Petronilo [1 ,2 ]
Montero, Isabel [3 ]
Teberio, Fernando [2 ]
Arregui, Ivan [2 ]
Percaz, Jon M. [2 ]
Lopetegi, Txema [2 ]
Arnedo, Israel [2 ]
Olano, Leandro [3 ]
Laso, Miguel A. G. [2 ]
机构：
[1] ESTEC, ESA, Noordwijk, Netherlands
[2] Univ Publ Navarra, Elect & Elect Engn Dept, Pamplona, Spain
[3] CSIC, Inst Ciencia Mat Madrid, Cient, Madrid, Spain
来源：
2017 IEEE MTT-S INTERNATIONAL MICROWAVE WORKSHOP SERIES ON ADVANCED MATERIALS AND PROCESSES FOR RF AND THZ APPLICATIONS (IMWS-AMP) | 2017年
关键词：
Waveguide filters; Additive Manufacturing; 3D printing; multipactor; SEY; high power;
D O I：
暂无
中图分类号：
TM [电工技术]; TN [电子技术、通信技术];
学科分类号：
0808 ; 0809 ;
摘要：
An in-depth secondary emission characterization for metal additive manufactured samples has been performed to assess the impact of the surface roughness in this parameter. Three samples has been 3D printed, post-processed with two different treatments and tested. The results shown a secondary emission improvement with considering as-built parts while is getting closer to the flat aluminum surface values when a post-process for improving the surface roughness is applied. The roughness from additively manufactured surfaced could be exploited to reduce the surface secondary emission and, hence, to increase the power for multipactor discharge.
引用
收藏
页数：3
相关论文
共 50 条
  • [31] Design considerations and modeling of fiber reinforced 3D printed parts
    van de Werken, Nekoda
    Hurley, Joel
    Khanbolouki, Pouria
    Sarvestani, Ali N.
    Tamijani, Ali Y.
    Tehrani, Mehran
    COMPOSITES PART B-ENGINEERING, 2019, 160 : 684 - 692
  • [32] ANALYSIS OF THE ANISOTROPY FOR 3D PRINTED PLA PARTS USABLE IN MEDICINE
    Gradinaru, Sebastian
    Tabaras, Diana
    Gheorghe, Dan
    Gheorghita, Daniela
    Zamfir, Raluca
    Vasilescu, Marius
    Dobrescu, Mircea
    Grigorescu, Gabriel
    Cristescu, Ioan
    UNIVERSITY POLITEHNICA OF BUCHAREST SCIENTIFIC BULLETIN SERIES B-CHEMISTRY AND MATERIALS SCIENCE, 2019, 81 (04): : 313 - 324
  • [33] Anisotropic and hyperelastic mechanical response of 3D printed TPU parts
    Martin-Sosa, Ezequiel
    Tavara, Luis
    Ojeda, Joaquin
    Estefani, Alejandro
    PROGRESS IN ADDITIVE MANUFACTURING, 2025,
  • [34] A review on voids of 3D printed parts by fused filament fabrication
    Tao, Yubo
    Kong, Fangong
    Li, Zelong
    Zhang, Jingfa
    Zhao, Xin
    Yin, Qing
    Xing, Dan
    Li, Peng
    JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2021, 15 : 4860 - 4879
  • [35] Rapid 3D-Plastronics prototyping by selective metallization of 3D printed parts
    Gerges, Tony
    Semet, Vincent
    Lombard, Philippe
    Allard, Bruno
    Cabrera, Michel
    ADDITIVE MANUFACTURING, 2023, 73
  • [36] Dimensional considerations on the mechanical properties of 3D printed polymer parts
    Elmrabet, Nabila
    Siegkas, Petros
    POLYMER TESTING, 2020, 90
  • [37] Effect of processing parameters on tensile strength of 3D printed parts
    Fajic, A.
    Tufekcic, Dz.
    Topcic, A.
    MECHANIKA 2008, PROCEEDINGS, 2008, : 123 - 128
  • [38] Microwave Characterization of 3D Printed Conductive Composite Materials
    Manzoor, Zahra
    Ghasr, Mohammad Tayeb
    Donnell, Kristen M.
    2018 IEEE INTERNATIONAL INSTRUMENTATION AND MEASUREMENT TECHNOLOGY CONFERENCE (I2MTC): DISCOVERING NEW HORIZONS IN INSTRUMENTATION AND MEASUREMENT, 2018, : 488 - 492
  • [39] FAILURE ANALYSIS AND QUALITY ASSESSMENT OF 3D PRINTED ABS PARTS
    Seif, Mohamed
    PROCEEDINGS OF THE ASME 13TH INTERNATIONAL MANUFACTURING SCIENCE AND ENGINEERING CONFERENCE, 2018, VOL 1, 2018,
  • [40] In situ real time defect detection of 3D printed parts
    Holzmond, Oliver
    Li, Xiaodong
    ADDITIVE MANUFACTURING, 2017, 17 : 135 - 142
12345