TAGUCHI PARAMETRIC STUDY ON THE RADIAL AND TANGENTIAL CUTTING FORCES IN DRY HIGH SPEED MACHINING (DHSM)

被引：0

作者：

Safari, H. ^{[1
]}

Hatami, M. ^{[1
]}

机构：

[1] Esfarayen Univ Technol, Dept Mech Engn, Esfarayen, North Khorasan, Iran

来源：

METALLURGICAL & MATERIALS ENGINEERING | 2020年 / 26卷 / 03期

关键词：

cutting force; titanium alloy; high speed machining; Taguchi method; SURFACE-ROUGHNESS; TITANIUM-ALLOY; INCONEL; 718; TOOL WEAR; OPTIMIZATION; DESIGN; TI-6AL-4V; STEEL;

D O I：

10.30544/472

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

In this paper, L-8 Taguchi array is applied to find the most important parameter effects on the radial and tangential cutting forces of a Ti-6Al-4V ELI titanium alloy in dry high speed machining (DHSM). The experiments are performed in four cutting speeds of 150, 200, 250, and 300 m/min and two feed rates of 0.03 and 0.06 mm/rev. Also, two cutting tools in types of XOMX090308TR-ME06 of uncoated (H25) and TiAlN+ TiN coated (F40M) are used. Results confirm that to minimize the resultant cutting force and radial cutting force, using the lower feed rate (0.03 mm/rev) and higher cutting speed (300 m/min) were considered as the best levels of studied factors.

引用

页码：303 / 316

页数：14

共 28 条

[1] Cytotoxic effects of Reactive Blue 33 on Allium cepa determined using Taguchi's L8 orthogonal array
Al, Gonca
Ozdemir, Utkan
Aksoy, Ozlem
[J]. ECOTOXICOLOGY AND ENVIRONMENTAL SAFETY, 2013, 98 : 36 - 40
[2] Development of a new lean lubrication system for near dry machining process
Aoyama, T.
Kakinuma, Y.
Yamashita, M.
Aoki, M.
[J]. CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2008, 57 (01) : 125 - 128
[3] Efficient fluoride removal by preparation, characterization of pyrolysis bone: Mixed level design experiment and Taguchi L8 orthogonal array optimization
Asgari, Ghorban
Dayari, Alireza
Ghasemi, Maryam
Seid-Mohammadi, Abdolmotaleb
Gupta, Vinod Kumar
Agarvval, Shilpi
[J]. JOURNAL OF MOLECULAR LIQUIDS, 2019, 275 : 251 - 264
[4] New observations on tool life, cutting forces and chip morphology in cryogenic machining Ti-6Al-4V
Bermingham, M. J.
Kirsch, J.
Sun, S.
Palanisamy, S.
Dargusch, M. S.
[J]. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2011, 51 (06) : 500 - 511
[5] An experimental investigation on effects of minimum quantity lubrication oil supply rate in high-speed end milling of Ti-6Al-4V
Cai, Xiao Jiang
Liu, Zhi Qiang
Chen, Ming
An, Qing Long
[J]. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2012, 226 (A11) : 1784 - 1792
[6] Dry machining of Inconel 718, workpiece surface integrity
Devillez, A.
Le Coz, G.
Dominiak, S.
Dudzinski, D.
[J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2011, 211 (10) : 1590 - 1598
[7] A comparative study of the cutting forces in high speed machining of Ti-6Al-4V and Inconel 718 with a round cutting edge tool
Fang, N.
Wu, Q.
[J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2009, 209 (09) : 4385 - 4389
[8] MODELING AND OPTIMIZATION OF FLANK WEAR AND SURFACE ROUGHNESS OF MONEL-400 DURING HOT TURNING USING ARTIFICIAL INTELLIGENCE TECHNIQUES
Hanief, M.
Charoo, M. S.
[J]. METALLURGICAL & MATERIALS ENGINEERING, 2020, 26 (01) : 57 - 69
[9] Optimization of a circular-wavy cavity filled by nanofluid under the natural convection heat transfer condition
Hatami, M.
Song, D.
Jing, D.
[J]. INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2016, 98 : 758 - 767
[10] Experimental optimization of the vanes geometry for a variable geometry turbocharger (VGT) using a Design of Experiment (DoE) approach
Hatami, M.
Cuijpers, M. C. M.
Boot, M. D.
[J]. ENERGY CONVERSION AND MANAGEMENT, 2015, 106 : 1057 - 1070

← 1 2 3 →