Selective laser melting of AlSi10 Mg: Influence of process parameters on Mg2Si precipitation and Si spheroidization

被引：70

作者：

Biffi, C. A. ^{[1
]}

Fiocchi, J. ^{[1
]}

Tuissi, A. ^{[1
]}

机构：

[1] CNR, Inst Condensed Matter Chem & Technol Energy, Unit Lecco, CNR ICMATE, Via Previati 1E, I-23900 Lecce, Italy

来源：

JOURNAL OF ALLOYS AND COMPOUNDS | 2018年 / 755卷

关键词：

Selective laser melting; Additive manufacturing; AlSi10; Mg; Thermal analysis; Microstructure; ALUMINUM-ALLOY; MECHANICAL-PROPERTIES; MELTED ALSI10MG; MICROSTRUCTURE; POWDER; ROUGHNESS; PRODUCTS; PROPERTY; STRENGTH; BEHAVIOR;

D O I：

10.1016/j.jallcom.2018.04.298

中图分类号：

O64 [物理化学（理论化学）、化学物理学];

学科分类号：

070304 ; 081704 ;

摘要：

In Selective Laser Melting (SLM) both structural and functional properties of built parts are drastically affected by the process parameters, such as laser beam power, exposure time and building platform temperature. The effect of the mentioned parameters on the microstructure evolution and mechanical properties of AlSi10 Mg SLM builts were investigated. It was found that chemical composition, melting point and phases morphology were not varied. On the contrary, thermal analysis indicated that Mg2Si precipitation as well as Si spheroidization phenomena were slightly affected by laser energy density. This effect becomes relevant for choosing the right thermal treatments required for mechanical property optimization of SLM built Al alloy components. (C) 2018 Elsevier B.V. All rights reserved.

引用

页码：100 / 107

页数：8

共 43 条

[31] Ragone D.V., 1995, THERMODYNAMICS MAT
[32] The influence of processing parameters on aluminium alloy A357 manufactured by Selective Laser Melting
Rao, Heng
Giet, Stephanie
Yang, Kun
Wu, Xinhua
Davies, Chris H. J.
[J]. MATERIALS & DESIGN, 2016, 109 : 334 - 346
[33] Selective laser melting of AlSi10Mg alloy: Process optimisation and mechanical properties development
Read, Noriko
Wang, Wei
Essa, Khamis
Attallah, Moataz M.
[J]. MATERIALS & DESIGN, 2015, 65 : 417 - 424
[34] Renishaw plc, 2014, LAS M AL ALSI10MG 25
[35] History of residual stresses during the production phases of AlSi10Mg parts processed by powder bed additive manufacturing technology
Salmi, Alessandro
Atzeni, Eleonora
[J]. VIRTUAL AND PHYSICAL PROTOTYPING, 2017, 12 (02) : 153 - 160
[36] Change in microstructure of selectively laser melted AlSi10Mg alloy with heat treatments
Takata, Naoki
Kodaira, Hirohisa
Sekizawa, Keito
Suzuki, Asuka
Kobashi, Makoto
[J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2017, 704 : 218 - 228
[37] Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder
Thijs, Lore
Kempen, Karolien
Kruth, Jean-Pierre
Van Humbeeck, Jan
[J]. ACTA MATERIALIA, 2013, 61 (05) : 1809 - 1819
[38] DEFECTS IN ALUMINUM QUENCHED FROM LIQUID STATE
THOMAS, G
WILLENS, RH
[J]. ACTA METALLURGICA, 1964, 12 (02): : 191 - &
[39] ON PRECIPITATION IN RAPIDLY SOLIDIFIED ALUMINIUM-SILICON ALLOYS
VANMOURIK, P
MITTEMEIJER, EJ
DEKEIJSER, TH
[J]. JOURNAL OF MATERIALS SCIENCE, 1983, 18 (09) : 2706 - 2720
[40] VANROOYEN M, 1989, METALL TRANS A, V20, P1207, DOI 10.1007/BF02647402

← 1 2 3 4 5 →