A comparative study on the shell and tube and gasket-plate heat exchangers: The economic viewpoint

被引：52

作者：

Hajabdollahi, Hassan ^{[1
]}

Naderi, Mehdi ^{[2
]}

Adimi, Sima ^{[3
]}

机构：

[1] Vali E Asr Univ Rafsanjan, Dept Mech Engn, Rafsanjan, Iran

[2] Urmia Univ, Dept Mech Engn, Orumiyeh, Iran

[3] Alborz Campus Univ Tehran, Dept Mech Engn, Karaj, Iran

来源：

APPLIED THERMAL ENGINEERING | 2016年 / 92卷

关键词：

Shell and tube heat exchanger; Gasket plate heat exchanger; Genetic algorithm; Total cost; MULTIOBJECTIVE OPTIMIZATION; THERMOECONOMIC OPTIMIZATION; DESIGN;

D O I：

10.1016/j.applthermaleng.2015.08.110

中图分类号：

O414.1 [热力学];

学科分类号：

摘要：

This paper presents a comparative study for optimization of gasket-plate and shell and tube heat exchangers. Total cost of the system (the capital and operating costs) is selected as objective function and Genetic Algorithm is applied to find the minimum of it for each case. Seven design parameters (decision variables) are used for gasket-plate while nine design parameters are selected for shell and tube heat exchanger. The optimum results show a noticeable improvement in the total cost in comparison with the results presented in the literature. For example, 35% improvement in the total cost is observed in the case of shell and tube compared with the literature. Furthermore, the comparison of the optimum results in the case of gasket-plate shows 13% improvement in the total cost compared with shell and tube heat exchanger with the same operating condition. Finally, sensitivity analysis for the change in the design parameters at the optimum point for each heat exchanger is performed and their results are reported. (C) 2015 Elsevier Ltd. All rights reserved.

引用

页码：271 / 282

页数：12

共 36 条

[1] Cost and Entropy Generation Minimization of a Cross-Flow Plate Fin Heat Exchanger Using Multi-Objective Genetic Algorithm [J].

Ahmadi, Pouria ;

Hajabdollahi, Hassan ;

Dincer, Ibrahim .

JOURNAL OF HEAT TRANSFER-TRANSACTIONS OF THE ASME, 2011, 133 (02)

[2]

[Anonymous], 1998, STAND TUB EXCH MAN A

[3]

[Anonymous], 2003, FUNDAMENTALS HEAT EX, DOI DOI 10.1002/9780470172605

[4] Optimal design of plate-and-frame heat exchangers for efficient heat recovery in process industries [J].

Arsenyeva, Olga P. ;

Tovazhnyansky, Leonid L. ;

Kapustenko, Petro O. ;

Khavin, Gennadiy L. .

ENERGY, 2011, 36 (08) :4588-4598

[5]

Bell K.J., 1988, Delaware method for shell-side design

[6]

Bell K.J., 1981, DELAWARE METHOD SHEL

[7]

Biniciogullari D., 2001, THESIS

[8] Heat exchanger design based on economic optimisation [J].

Caputo, Antonio C. ;

Pelagagge, Pacifico M. ;

Salini, Paolo .

APPLIED THERMAL ENGINEERING, 2008, 28 (10) :1151-1159

[9] Thermoeconomic optimization of baffle spacing for shell and tube heat exchangers [J].

Eryener, D .

ENERGY CONVERSION AND MANAGEMENT, 2006, 47 (11-12) :1478-1489

[10]

Garrett-Price BA., 1985, FOULING HEAT EXCHANG

← 1 2 3 4 →