Effect of Shear Resistance on Flexural Debonding Load-Carrying Capacity of RC Beams Strengthened with Externally Bonded FRP Composites

被引：9

作者：

Li, Guibing ^{[1
]}

Zhang, Aihui ^{[2
]}

Jin, Weiliang ^{[3
]}

机构：

[1] Shandong Inst Business & Technol, Dept Management Sci & Engn, Yantai 264005, Peoples R China

[2] Zhejiang Univ, Coll Civil Engn & Architecture, Hangzhou 310058, Zhejiang, Peoples R China

[3] Zhejiang Univ, Ningbo Inst Technol, Ningbo 315100, Zhejiang, Peoples R China

来源：

POLYMERS | 2014年 / 6卷 / 05期

关键词：

reinforced concrete (RC) beam; carbon fiber reinforced polymer (CFRP)-strengthened; shear resistance; flexural debonding load-carrying capacity; REINFORCED-CONCRETE BEAMS; FAILURE; ANCHORAGE; DESIGN; MODELS; JOINTS; PLATES; INTERFACE; STRESS; PREDICTION;

D O I：

10.3390/polym6051366

中图分类号：

O63 [高分子化学（高聚物）];

学科分类号：

070305 ; 080501 ; 081704 ;

摘要：

Debonding failure is the main failure mode in flexurally strengthened reinforced concrete beams by externally bonded or near surface mounted fibre reinforced polymer (FRP) composites. It is believed that FRP debonding will be initiated if the shear stress on the concrete-FRP interface reaches the tensile strength of concrete. However, it was found through experimental and analytical studies that the debonding mechanism of FRP composites has the potential of shear failure in combination with debonding failure. Moreover, the shear failure probably influences the debonding failure. Presently, there are very little experimental and analytical studies to investigate the influence of shear resistance of reinforced concrete (RC) beam on FRP debonding failure. The current study investigates and analyzes the effect of shear resistance on FRP debonding failure based on test results. The analytical results show that the shear resistance of RC beam has a great effect on flexural debonding load-carrying capacity of FRP-strengthened RC beam. The influence of shear resistance on flexural debonding load-carrying capacity must be fully considered in flexural strengthening design of RC beams.

引用

页码：1366 / 1380

页数：15

共 50 条

[1]

ACI 440.2R-08, 2008, ACI 440.2R-08, P76

[2] Interfacial stress transfer of near surface-mounted FRP-to-concrete joints [J].

Ali, M. S. Mohamed ;

Oehlers, D. J. ;

Griffith, M. C. ;

Seracino, R. .

ENGINEERING STRUCTURES, 2008, 30 (07) :1861-1868

[3]

[Anonymous], 2004, DT200 CNR NAT RES CO, P164

[4]

[Anonymous], 2001, FIB B, P51

[5]

[Anonymous], 2001, CONCR ENG SER, V41, P31

[6]

[Anonymous], 2010, COD DES CONCR STRUCT, P425

[7]

[Anonymous], 2007, DOBOKU GAKKAI RONBUN

[8] Design by testing procedure for intermediate debonding in EBR FRP strengthened RC beams [J].

Bilotta, A. ;

Faella, C. ;

Martinelli, E. ;

Nigro, E. .

ENGINEERING STRUCTURES, 2013, 46 :147-154

[9] FRP-to-concrete interface debonding: Experimental calibration of a capacity model [J].

Bilotta, Antonio ;

Di Ludovico, Marco ;

Nigro, Emidio .

COMPOSITES PART B-ENGINEERING, 2011, 42 (06) :1539-1553

[10]

BUYUKOZTURK O., 2002, 15th ASCE Engineering Mechanics Conference, Columbia University, New York, NY, P1

← 1 2 3 4 5 →