Developments in Tribology of Manufacturing Processes

被引：13

作者：

Schmid, S. R. ^{[1
]}

Saha, P. K. ^{[2
]}

Wang, J. ^{[3
]}

Schmitz, T. ^{[4
]}

机构：

[1] Univ North Carolina Charlotte, Dept Mech Engn & Engn Sci, Charlotte, NC 28223 USA

[2] Boeing Co, Seattle, WA 98124 USA

[3] Texas A&M, Dept Engn Technol & Ind Distribut, College Stn, TX 77843 USA

[4] Univ Tennessee, Dept Mech Aerosp & Biomed Engn, Knoxville, TN 37996 USA

来源：

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME | 2020年 / 142卷 / 11期

关键词：

bulk deformation processes (e; g; extrusion; forging; wire drawing; etc; machining processes; modeling and simulation; sheet and tube metal forming; tribology in manufacturing; HIGH-PRESSURE COOLANT; TOOL-WEAR; HYDRODYNAMIC LUBRICATION; STAMPING LUBRICANTS; TI-6AL-4V ALLOY; SURFACE INTEGRITY; WORK ROLL; OIL; SHEET; PERFORMANCE;

D O I：

10.1115/1.4047723

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Tribology in manufacturing has seen tremendous development in the past 100 years and essentially was transformed from a known and unavoidable nuisance to a sophisticated discipline. This is demonstrated by the reliability and quality of products that result in modern metal forming and cutting. This paper provides a brief summary of the state-of-the-art in manufacturing tribology, discussing some of the important developments in the field.

引用

页数：11

共 119 条

[1] Using PCD for machining CGI with a CO2 coolant system [J].

Abele, Eberhard ;

Schramm, Burkhard .

PRODUCTION ENGINEERING-RESEARCH AND DEVELOPMENT, 2008, 2 (02) :165-169

[2] An accurate numerical solution for the singular velocity field near the maximum friction surface in plane strain extrusion [J].

Alexandrov, Sergei ;

Kuo, Chih-Yu ;

Jeng, Yeau-Ren .

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES, 2018, 150 :107-116

[3] Generation of a Fine Grain Layer in the Vicinity of Frictional Interfaces in Direct Extrusion of AZ31 Alloy [J].

Alexandrov, Sergei ;

Jeng, Yeau-Ren ;

Hwang, Yeong-Maw .

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME, 2015, 137 (05)

[4]

Altintas Y., 2000, MANUFACTURING AUTOMA, DOI DOI 10.1017/CBO9780511843723

[5]

[Anonymous], 1878, Proc. I. Mech. E. Lond, DOI DOI 10.1243/PIME_PROC_1878_029_017_02

[6]

[Anonymous], 1990, CIRP Ann., DOI DOI 10.1016/S0007-8506

[7]

[Anonymous], 1984, TRIBOLOGY METALWORKI

[8] Analysis of the influence of tool type, coatings, and machinability on the thermal fields in orthogonal machining of AISI 4140 steels [J].

Arrazola, P. J. ;

Arriola, I. ;

Davies, M. A. .

CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2009, 58 (01) :85-88

[9] The mechanisms of chip formation in machining hardened steels [J].

Barry, J ;

Byrne, G .

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME, 2002, 124 (03) :528-535

[10]

Barus C, 1893, Am. J. Sci., Vs3-45, P87, DOI [10.2475/ajs.s3-45.266.87, DOI 10.2475/AJS.S3-45.266.87]

← 1 2 3 4 5 6 7 8 9 10 →